background image

MULTI-LINK PLUG-IN

DESCRIPTION

The Multi-Link Plug-In control features both the ease of plug-in installation and the convenience of 
radio remote control.  This single motor control is RTS compatible and plugs into a standard AC outlet.  
A Somfy motor plugs directly into the control, eliminating the need for additional wiring.

Part Number:  9012781

CONNECTION DIAGRAM

Motor Connector

N

E

U

T

R
A

L

D

I

R

1

D

I

R

2

G

R

O

U
N
D

1.

  Insert a screwdriver into the square holes to reveal the opening in the circular hole.  Insert 

     the appropriate motor wire and remove the screwdriver.

2.

  When all the motor wires have been connected, snap on the bottom of the included strain 

     relief.  Anchor the wires using the wire tie.  Attach the top of the strain relief. 

End View of Plug-In Module

Programming Button

Sequence Button

MANUAL OPERATION 

Upon Power-Up, the MultiLink Plug-In is unprogrammed and will only respond to the Sequence Button or programming commands from a transmitter

To operate the MultiLink Plug-in manuually, pressing the Sequence button will cycle through the directions as follows:
          DEPRESS 1:  UP DIRECTION
          DEPRESS 2:  STOP DIRECTION
          DEPRESS 3:  DOWN DIRECTION
          DEPRESS 4:  STOP DIRECTION

SOMFY SYSTEMS, INC.  4/07

C

SOMFY CANADA

6315 Shawson Drive, Unit #1
Mississauga, Ontario L5T1J2

SOMFY SYSTEMS, INC. reserves the right to change, 
update or improve this document without prior notice.

Ref. No. 2500995

SOMFY SYSTEMS, INC.

47 Commerce Drive 
Cranbury, NJ 08512

SOMFY MEXICO S.A. De C.V.

Calle 3 No.47, Loc.E-5
Fracc Ind. Alce Blanco
Nau.,Edo. de Mex C.P. 53370,Mex

PROGRAMMING GUIDELINES

The following guidelines should be applied when installing a Multi-Link Plug-In control:

- The antenna MUST protrude outside of the enclosure and should not be close to high voltage wires.
- When installing multiple controls, each control must be separated by 12 inches minimum.
- When installing multiple controls, it is recommended having only 1 Multi-Link powered at a time during programming. 
- The Multi-Link Plug-in can memorize up to 8 Telis Transmitter (or similar) channels.

Summary of Contents for MULTI-LINK PLUG-IN

Page 1: ...tton or programming commands from a transmitter To operate the MultiLink Plug in manuually pressing the Sequence button will cycle through the directions as follows DEPRESS 1 UP DIRECTION DEPRESS 2 STOP DIRECTION DEPRESS 3 DOWN DIRECTION DEPRESS 4 STOP DIRECTION SOMFY SYSTEMS INC 4 07 C SOMFY CANADA 6315 Shawson Drive Unit 1 Mississauga Ontario L5T1J2 SOMFY SYSTEMS INC reserves the right to change...

Page 2: ...lternately an additional transmitter can be programmed into memory by following the steps to memorize the initial transmitter as outlined in A above 4 Repeat these steps for each additional transmitter or channel up to 8 total to be stored in memory If a 9th channel or transmitter programming is attempted the MultiLink will respond by jogging the window treatment but any commands will be ignored B...

Page 3: ... Time RUN TIME 1 Make sure the shade is not at the upper limit Enter programming mode by pressing the UP and DOWN buttons of a Telis Transmitter simultaneously The window treatment will respond by jogging UP then DOWN 2 Press and release the UP button 7 times pausing after each switch press to verify the motor jogs UP After the seventh jog press and release the STOP button until the motor jogs 3 P...

Page 4: ...ach time the UP button is pressed Below is a summary of the number of UP key presses and the corresponding function D A Memory Clear can be performed by pressing the Programming Button on the Plug In Unit or via the transmitter MULTILINK PLUG IN Quick Reference Guide Enter Intermediate Position Setup Disable or Enable Tilt Function Erase all programmed functions and memorized transmitters Disable ...

Reviews: