3.4 Remove a control
3.5 Complete reset (back to factory configuration)
3.3 Record a new control
3.2 Operating
3V
LITHIUM
RENA
TA
CR 2430
S
W
IS
S
M ADE
3V
LITHIUM
RENA
TA
CR 2430
Note : When you enter in programming mode with an already recorded control, you cannot erase it
➜
or
With a RTS control
With a RT control
With the built in control button
Press briefly the
▲
button to switch the lamp ON.
Press briefly the
■
or
▼
buttons to switch the lamp OFF.
ON
OFF
ON/OFF
Press briefly on the front button of the RT
control to switch the lamp ON or OFF.
You can also control the lamp with the push button
located on the LIGHTING outdoor RTS.
3
Trouble shooting guide
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
Nothing works:
ð
Check the light.
ð
Check the power supply.
ð
Check the battery of the transmitter.
ð
Check that the transmitter has been properly recorded in the LIGHTING outdoor RTS memory (section 3).
ð
Check for any other possible source of radio interferences.
Lost in your programming mode:
ð
Just make a complete reset and start again.
0,5 s
0,5 s
0,5 s
or
3V
LITHIUM
RENA
TA
CR 2430
S
W
IS
S
M ADE
3V
LITHIUM
RENA
TA
CR 2430
Press for more than 2 sec. on the programming button of the LIGHTING outdoor
RTS or use an already recorded control.
RTS control : press for more than 2 sec. on the “prog” button.
RT control : remove the battery, press briefly the button, replace the battery and
press for more than 2 sec. on the button.
➜
The LED of the LIGHTING outdoor RTS lights on and the lamp lights for 2 secs.
RTS control : press briefly the “prog” button.
RT control : remove the battery, press briefly the button, replace the
battery and press again briefly the button.
➜
The lamp lights during 2 secs. again and the LED of the LIGHTING
outdoor RTS blinks during 5 sec. The new control is recorded.
RTS control : press briefly the “prog” button.
RT control : remove the battery, press briefly the button, replace the
battery and press again briefly the button.
➜
The lamp lights during 2 secs. again and the LED of the LIGHTING
outdoor RTS blinks during 5 sec. The control has been erased.
1
2
1
2
Set the LIGHTING outdoor RTS in its programming mode :
Record the new control :
Remove the control :
➜
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
➜
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
2 s
0,5 s
0,5 s
0,5 s
0,5 s
or
or
2 s
2 s
N
L
N
L
N
L
➜
Press for more than 7 seconds the programming button of the
LIGHTING outdoor RTS
until the
LED lights.
➜
The LED lights up after 2 seconds and blinks after 7 seconds Then, the lamp lights during 2 secs.
the
LIGHTING outdoor RTS
has been completely cleared and no more controls are recorded.
You have then to re-program the
LIGHTING outdoor RTS
from the first step of programming
(refer to the section 3.1 “Record the first control”).
N
L
2 s
already recorded control
or
Press for more than 2 sec. on the programming button of the LIGHTING outdoor
RTS or use an
already recorded control
.
RTS control : press for more than 2 sec. on the “prog” button.
RT control : remove the battery, press briefly the button, replace the battery and
press for more than 2 sec. on the button.
➜
The LED of the LIGHTING outdoor RTS lights on and the lamp lights for 2 secs.
Set the LIGHTING outdoor RTS in its programming mode :
5 s
2 s
N
L
5 s
2 s
N
L
5 s
ON/OFF
2 s
➜
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
2 s
0,5 s
or
2 s
N
L
N
L
2 s
already recorded control
or
2 s
N
L
7 s
SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230
All rights reserved to makes changes without prior notice.