Trouble shooting guide
CENTRALIS UNO RTS VB
is a individual control system for AC motor dedicated to external and
interior venetian blind applications.
•
CENTRALIS UNO RTS VB
has an integrated radio receiver compatible with the RT
and RTS transmitters allowing individual, group and master commands. Up to twelve controls can
be recorded in the
CENTRALIS UNO RTS VB
.
•
The commands coming from the radio controls can be disabled thanks to the 0/auto switch.
• An automatic intermediate position and a slat tilting operation can be programmed.
•
CENTRALIS UNO RTS VB
is compatible with the EOLIS and SOLIRIS sensors RTS.
Up to three RTS sensors can be memorized in one receiver and one RTS sensor can be memori-
zed in several receivers.
inteo
CENTRALIS UNO RTS VB
INSTALLATION
guide
Ref.5005937A
80 mm
80 mm
33 mm 17 mm
• Main supply : 220-240V 50Hz.
• Class II product
• Protection index IP40.
• Output : 250V~ 3A
• Output temporisation : activ for 180s.
• Environmental conditions for use :
- tempe5°C to +40°C (no condensation allowed).
- pollution degree typical for usual living space.
This device must be installed and programmed by qualified installers for whom this instruction is inten-
ded.
Before connecting the unit, read the instructions carefully.
We reserve the right to make changes due to technical improvements.
1
CENTRALIS uno RTS VB
FRONT PLATE
CONTROL UNIT
FRAME
BRACKET
WALL
1
Characteristics
2
Installation
The range of radio control is limited by laws regulating
radio devices and by building design.
When planning, please ensure that there is adequate radio
reception.
In order not to affect quality of reception, a minimum
distance of 30 cm between a
CENTRALIS uno RTS VB
and a radio transmitter should be maintained.
CENTRALIS uno RTS VB
should not be installed in the
immediate vicinity of metal surfaces. Powerful local trans-
mitter equipment (e.g. cordless headphones) with a trans-
mission frequency identical to the
CENTRALIS uno RTS
VB
can affect its function.
Hereby, SOMFY, declares that this equipment
is in compliance with the essential require-
ments and other relevant provisions of
Directive 1999/5/EC.
A Declaration of Conformity is available at the
web address
www.somfy.com
Heading
CE
We reserve the right to make changes due to technical improvements.
CENTRALIS uno RTS VB
4
Nothing works:
§
Check the wiring.
§
Check the battery of the transmitter.
§
Check that the transmitter has been properly recorded.
§
Check for any other possible source of radio interferences.
Lost in your programming mode:
§
Just make a complete reset and start again
(refer to section 5).
• Move the blind at its
UP
limit with
the
▲
button and immediately press
the
■
button briefly.
• Press the
▼
and
■
button simulta-
neously until the blind begins to move
DOWN
.
• Stop the blind at the intermediate
position you wish.
If necessary, adjust this position with
the
▲
or
▼
buttons.
• Press the
■
button more than 5 sec.
➜
The blind jogs briefly (UP/DOWN),
the intermediate position is recorded.
• Press simultaneously on the
▲
and
■
button until the blind begins
to move briefly
UP
.
• Move the blind downward to get
the slats closed.
• Adjust the tilt angle with the
▲
or
▼
buttons.
• Press the
■
button more than 5 sec.
➜
The blind jogs briefly (UP/DOWN), the
tilt angle is recorded.
after
3 seconds
STOP
IP
• Press briefly the
■
button while the
blind is at its
UP limit
.
➜
The blind will move and stop at the
intermediate position.
• Press briefly the
■
button while the blind is at its UP limit.
➜
The blind will move, stop at the intermediate position and tilt at
the pre-set angle.
Note : after a DOWN movement the blind only tilts.
• Press briefly the
■
button while the blind
is closed (after a DOWN movement).
➜
The blind will tilt at the pre-set angle.
Note : after an UP movement the blind
does not tilt.
adjust
the angle
Set the blind to its UP limit before programming in order to always have the same adjustment.
If IP only has been programmed
If tilting only has been programmed
If both IP and tilting have been programmed
2
1
3
1
2
3
4
4
5 sec.
5 sec.
Phantom intermediate position/slat tilting:
§
The programmed IP can only be reached from the UP limit.
not when the blind is in another position.
§
Be sure to adjust the slat tilting after a down movement
when the blind is approximately 3/4 down of the window.
after
3 seconds
or
UP
UP limit
UP limit
tilting
tilting
IP
IP
SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230
Assembly
2.1
Programming the intermediate position
(IP)
a
Programming the automatic slat tilting
b
Operating
c
If you record a new IP or a new tilting function, this will automatically erase the previous one.
If you want to erase without recording a new one, Press briefly on the
■
button to reach the IP or to get the tilting (or both), then:
§
To erase the intermediate position, press the
▼
and
■
buttons simultaneously for more than 5 seconds.
§
To erase the tilting, press the
■
and
▲
buttons simultaneously for more than 5 seconds.
§
To erase both, just press the
■
button for more than 5 seconds.
➜
The blind jogs briefly (UP/DOWN) indicating that
CENTRALIS uno RTS VB
has deleted the intermediate position and/or the tilting.
Delete the intermediate position/automatic tilting
d
5
Complete reset
To completely reset the CENTRALIS uno RTS VB, press its PROG button for more than 7 seconds.
This will erase all of the programmed controls, the intermediate position and the automatic tilting.
➜
The blind jogs briefly (UP/DOWN), the memory of the CENTRALIS uno RTS VB is cleared.
P
R
O
G
7 sec.
usable in EU, CH
