When using a resistive sensor bar, the latter must be wired onto safety input 1.
The opening safety device stops then recloses partially (non configurable action).
The safety action at opening (P1, P2, or P3 = 01) is not configurable (stopage followed with partial door reopening).
However, safety actions upon closing (P1, P2, or P3 = 02) can be configured:
=
Stop the door.
=
Stop, then total reopening of the door
(default mode)
=
Stop then partial reopening of the door
(2 seconds operation)
The self-test function is used to check proper operation of the safety accessories automatically at the
end of closing.
CYCLE COUNTERS
EVENT CODES
Axroll waiting for a command
Opening door
Wait before closing the door
Closing door
Open cell hidden
Close cell hidden
ADMAP cell hidden
Door movement forced by keypad
Emergency stop triggered
Self-testing safety
Permanent contact on “START” input
Wait before motor reversion
FAULT CODES
Safety fault at opening (contact always open)
Safety fault at closing (contact always open)
ADMAP safety fault (contact always open)
Self-test failed on safety input 1
Self-test failed on safety input 2
Self-test failed on safety input 3
Intensity exceeded on 24V power supply (too many accessories connected)
Operating time “
T0
” too short or motor endstop not reached
Log of the last 10 faults
....
See fault code above.
Reinitialise the Axroll after a fault
To clear the fault codes, select the parameter
and press and holding the
“
+
”key for 3 seconds until dashes appear “
-.-
”
For the fault codes from
to
:
Once the fault is corrected, it is not required to clear the fault code of the
log to return to normal operation.
For defect codes from
to
:
Once the fault is corrected, you must clear the defect code for
the log to return to normal operation.
“0” to “99” Watts
* If the connection of accessories matches the diagram in chapter 1.
**
A
rea
D
angerous for
M
ovement
A
ccessible to
the P
ublic.
Motor operating time
(Increment of 1 sec.)
Adjust a time slightly longer than the actual operating time.
Tens and units
Thousands and hundreds
Hundred and tens of thousands
ACCESSORY CONSUMPTION
power consumed in Watts
3.2 Safety input function: parameters
3.3 Safety action upon closing: parameter
(plant value = 01)
3.4 Configuration of the self-testing function: parameters
Time for reclosing the door
(Increment of 1 sec.)
Enabled in automatic operating modes (§ 3.1)
Waiting time before motor reversion
Particular case of motors not accepting reversion of the rotation
direction without stopping phase.
(Increment of 1 sec.)
The Axroll can be controlled in the three-button mode using a reverter with three keys wired onto the START,
SEC2, and SEC3 inputs (if the latter are configured “non wired”: chapter 3.2).
Area lighting time after cycle end
(Increment of 1 min.)
+
Clearing all remote controls is performed by pressing and holding for
3 seconds the key “
+
” until dashes appear “
-.-
”
3 sec.
3 sec.
long press
Opening
Stop
Closing
According to the type of operation chosen in chapter 3.1, the value of the P8 parameter does not
produce the same effects.
Automatic, semi-automatic, or sequence modes.
3-button mode
3.5 Programming remote controls: parameter
3.6 Clearing remote controls: parameter
(plant value = 04)
3.7 Configuration of auxiliary accessories: parameter
3.8 Configuring the operating mode: parameters
to
=
Opening/Closing Command
(default mode)
.
=
Auxiliary output control
(driving the accessory connected to the AUX output).
=
Open command
=
Close command
=
Stop command
=
Auxiliary output control
(driving the accessory connected to the AUX output).
Press simultaneously the remote control key to
program and the key
“
+
“ on the Axroll for three seconds until
dashes appear “
-.-
”
DIsplay the value of the function to program using
the “
+
“ and “
-
“ keys on the Axroll.
Choose the remote control key's function to program.
Opening
Stop
Closing
Auxiliary
Opening
Stop
Closing
1
Save the code
(Axroll can save maximum 32 channels)
2
Self-testing safety input 1: parameter
(plant value = 00)
=
No self-test of the accessory connected
(default mode)
=
Self-test for photocells by power supply cutting.
(caution, the transmitting cell must be supplied on terminals 10/12 and the receiver cells on terminals 10/11).
=
Self-test for accessory fitted with a TEST input
(cells or sensor bar).
=
Self-test for resistive sensor bar (value comprised between 5 and 14 K
Ω
).
Configuration of safety input 1 (sensor bar*): parameter
(plant value = 00)
=
No accessories connected to safety input 1
(default mode)
=
Accessory connected to safety input 1 enabled when opening the door
=
Accessory connected to safety input 1 enabled when closing the door
=
ADMAP** safety: active upon c forbids starting at opening
=
Contact for connecting an emergency stop device
Configuration of safety input 2 (photocell*): parameter
(plant value = 00)
=
No accessories connected to safety input 2
(default mode)
=
Accessory connected to safety input 2 enabled when opening the door
=
Accessory connected to safety input 2 enabled when closing the door
=
ADMAP** safety: active upon c forbids starting at opening
=
Contact for connecting an emergency stop device
Configuration of safety input 3: parameter
(plant value = 00)
=
No accessories connected to safety input 3
(default mode)
=
Accessory connected to safety input 3 enabled when opening the door
=
Accessory connected to safety input 3 enabled when closing the door
=
ADMAP** safety: active upon c forbids starting at opening
=
Contact for connecting an emergency stop device
The auxiliary contact is a dry contact. A single accessory can be connected and power supplied according to the use configured.
=
Contact to drive an electric latch
(The latch must be supplied with an outside power supply)
=
Contact to drive an electromagnetic latch
=
Contact to drive an Orange flashlight without notice
(only during the door’s operation)
=
Contact to drive an Orange flashlight with notice
(before starting and during door’s operation)
=
Contact to drive a zone lighting
(default mode, automatic switch off after timeout T3 § 3.8)
=
Contact to drive an open door indicator
=
Contact of the stable mono relay type to drive an automation system
=
Contact of the bi-stable relay type to drive an automation system
Self-testing safety input 2: parameter
(plant value = 00)
=
No self-test of the accessory connected
(default mode)
=
Self-test for photocells by power supply cutting.
(caution, the transmitting cell must be supplied on terminals 10/12 and the receiver cells on terminals 10/11).
=
Self-test for accessory fitted with a TEST input
(cells or sensor bar).
Self-testing safety input 3: parameter
(plant value = 00)
=
No self-test of the accessory connected
(default mode)
=
Self-test for photocells by power supply cutting.
(caution, the transmitting cell must be supplied on terminals 10/12 and the receiver cells on terminals 10/11).
=
Self-test for accessory fitted with a TEST input
(cells or sensor bar).
Operating information
4
safety 1: P1+P5
safety 2: P2+P6
safety 3: P3+P7
Ensure you configure the safety input used for
the appropriate self-test:
Once the safety accessories are connected and the safety inputs configured,
check manually the proper operation of the accessories before the final
start up of the facility.
List of operating information displayed by Axroll used to view and an easy diagnostic of the facility’s status.
To return to the menu, press the “
“ or “
“ keys to return to value C1 (or any other value indicating the product’s
operation: see § 4) or after a one-minute waiting time.
