EN
A
MOUNTING
[1]
Choose the optimal location: flat and large surface
[2]
Mount the KNX 4 DC Motor Controller WM
[3]
Use cable tie!
[4]
Keep to minimum distance
B
CABLING
[1] Tool for all terminals
[2] Wiring diagram
[3]
Check the correct running direction of the end product
UP: the end product goes up ( C +
)
STOP: the end product stops ( C +
+
)
DOWN: the end product goes down ( C +
)
m
To close window press UP, to open window press DOWN.
[4]
Possible switches
1.
Smoove Origin IB, Ref. 1811272
2.
Double push button
C
COMMISSIONING AND OPERATING
[1] Reset/Prog button
Is the access to the basic configuration of the Motor Controller.
[2] Selection of the push button ergonomic
Local push button ergonomics and the type of end products to be preselected:
• Screen mode (SCR)
• Venetian blind, European mode
• Venetian blind, US mode (default mode)
1.
To toggle between modes, press shortly the Reset / Prog button. Repeat
until the LED, according to the desired configuration, lights up.
2.
Save and exit
[3] Factory RESET
[4] Learn running time/length
1.
Drive screen to upper end limit
2.
Press Stop until screen drives down on its own
3.
Press shortly Stop when lower end limit is reached
[5] Learn and recall intermediate position (IP)
1.
Recording
2.
Recalling
CHARACTERISTICS
Supply voltage
24 V DC (min. 21.5 V - max. 28 V DC)
Power Supply
Regulated and short circuit proof power supply, certified and suitable for the connected motors
Stand-by current / Stand-by power (IEC 62301)
25 mA@24 V DC / 600 mW@24 V DC
Supply voltage from KNX bus
KNX voltage 21 ... 30 V DC, SELV
Rated current consumption KNX
As per KNX guidelines, 10 mA
Max. motor current consumption
4 x 2.5 A@24 V DC
Supply voltage of group control input
SELV, 16 V DC
Supply voltage of local push buttons
SELV, 16 V DC
Terminals
Spring connectors
Relay micro-gap
μ
Terminal KNX
KNX bus terminal (black/red)
Running time per output
Max. 5 minutes
Operating temperature
- 5 ° C ... + 45 ° C
Relative humidity
Max. 85 %
Material of housing
PC-ABS
Housing dimensions (w x h x d)
180 x 255 x 61 mm
Weight
710 g
Degree of protection
IP 20
Protection class
Pollution degree
2
Conformity
www.somfy.com/ce
We care about our environment. Do not dispose of the appliance with usual household waste. Give it to an approved collection point for recycling.
CABLE
Connection to ... Cable
Twisted pair
Max. length
Stripping length
Motors
Min.: 2 x 0.6 mm/22 AWG / Max.: 2 x 2.5 mm
2
/13 AWG –
6 mm/0.24“
Switch
Min.: 3 x 0.6 mm/22 AWG / Max.: 3 x 2.5 mm
2
/13 AWG Recommended
100 m/330 ft
6 mm/0.24“
Group control
Min.: 3 x 0.6 mm/22 AWG / Max.: 3 x 1.5 mm
2
/15 AWG Recommended
100 m/330 ft
6 mm/0.24“
KNX bus
2 x 0.8 mm/20 AWG
Required, following KNX topology guidelines
6 mm/0.24“
24 V DC
Min.: 2 x 1.5 mm
2
/15 AWG / Max.: 2 x 2.5 mm
2
/13 AWG –
10 m/33 ft
6 mm/0.24“
m
Control of non Somfy motors only on request and after approval by Somfy
animeo
KNX 4 DC Motor Controller WM. Ref. 5138035A -
8/20
CORRECTION LOOP 2
