35
Safe
ty / Exp
ort
Please read and observe ...
Safety
• All danger and safety notes attached to the device must be observed!
• No safety equipment (e.g. panel switch) or safety notes may be re-
moved or deactivated which can impair the safe operation of the de-
vice!
• The device may only be operated in proper condition!
1) In Germany: VDE regulations
• A timing device must be designed so that the device is automatically
switched off at the latest after <110% of the selected operating time
even when the controller fails. The device operating time must be
dual controlled with a timing device in accordance with EN 60335-2-
27.
• Do not change, obstruct or block the air inflow and outflow area to the
device or make any unauthorised changes to the device. The manu-
facturer shall bear no liability for damage or injuries resulting from
such actions.
• Before putting a tanning device into operation, the transport pallet
must be removed from under the device. Danger of overheating by
obstruction of the air routing.
Danger!
Assembly and electrical connection must comply with the na-
tional regulations.
1)
The electrical installation is to be fitted with an easily accessible
all pole isolating device (master switch) on the building side,
complying with overvoltage category III. This means that each
pin shall have a contact opening width complying with the con-
ditions of overvoltage category III for full isolation.
If it is connected via a plug and socket, the plug system used
shall comply with EN 60309-1/A11; 5-pin; 400 V AC -
(16A or 32A) shall be used.
Assembly, installation, upgrading or repair of the device may
only be carried out by specially trained and instructed person-
nel.
Caution!
The code for access via the infrared interface is preset in the
software of the hand-held unit, and can therefore be used with
any unit. Anyone, who downloads the software from the Internet
can access the unit date with a hand-held unit. Please note that
Customer Service changes the preset access code during initial
start-up – see Page 102. Please note the new code for future
use!
This code is independent of the access code for the presettings
via the control panel.
Summary of Contents for S-45 Hot Pepper Super Series
