8
Installation Instructions
7
It’s important to carefully read the following installation
instructions before beginning the installation of your oven.
Important installation safety –
Always switch the power off prior to beginning the installation.
–
Stainless steel is very easily damaged during installation. Wherever possible,
protect the rangehood with the cardboard box or plastic wrap during the
installation.
–
For safety reasons, this Rangehood must be earthed.
–
A power point must be located within 1.5m of the power cord exit from the
rangehood, and it should be always accessible to allow isolation from power
during cleaning or maintenance.
–
A 150mm round ducting adapter is supplied, however all other ducting
accessories are not.
–
All ducting must comply with building codes and local requirements.
–
If you are re-circulating the air, rather than ducting, please ensure that the side
outlet grilles are not obstructed in any way as this will effect the effi ciency of
the rangehood.
–
Ensure that the rangehood is mounted in a level position, both horizontally
and vertically. This is essential to ensure the rangehood operates correctly and
prevents grease build
up at one end.
Ducting options
Before beginning the installation of your rangehood, the method of ducting should be
considered and selected. The guide below illustrates the various ducting options.
Note:
This rangehood can be operated in recirculation mode where required,
although
Esatto
recommends to duct wherever possible.
1.
Into your ceiling cavity and then vented through your eaves.
2.
Straight up and through your tiled or metal roof.
INSTALLATION INSTRUCTIONS
This rangehood cannot be operated in recirculation mode,
Sôlt recommends to duct wherever possible.
7
It’s important to carefully read the following installation
instructions before beginning the installation of your oven.
Important installation safety –
Always switch the power off prior to beginning the installation.
–
Stainless steel is very easily damaged during installation. Wherever possible,
protect the rangehood with the cardboard box or plastic wrap during the
installation.
–
For safety reasons, this Rangehood must be earthed.
–
A power point must be located within 1.5m of the power cord exit from the
rangehood, and it should be always accessible to allow isolation from power
during cleaning or maintenance.
–
A 150mm round ducting adapter is supplied, however all other ducting
accessories are not.
–
All ducting must comply with building codes and local requirements.
–
If you are re-circulating the air, rather than ducting, please ensure that the side
outlet grilles are not obstructed in any way as this will effect the effi ciency of
the rangehood.
–
Ensure that the rangehood is mounted in a level position, both horizontally
and vertically. This is essential to ensure the rangehood operates correctly and
prevents grease build
up at one end.
Ducting options
Before beginning the installation of your rangehood, the method of ducting should be
considered and selected. The guide below illustrates the various ducting options.
Note:
This rangehood can be operated in recirculation mode where required,
although
Esatto
recommends to duct wherever possible.
1.
Into your ceiling cavity and then vented through your eaves.
2.
Straight up and through your tiled or metal roof.
INSTALLATION INSTRUCTIONS
8
Through your wall
Further to your various ducting options, below are some
tips on how to correctly duct your rangehood:
– Always use correctly sized ducting
— DO NOT reduce the size of the ducting
– Always use solid ducting
– Always use non-flammable ducting
– Always duct to the outside atmosphere
– Do not use flexible ducting
– Do not duct into the ceiling space- always vent to the
outside atmosphere.
– Avoid sharp 90 degree bends as much as possible,
use 45 degree bends instead wherever possible
– Duct to the outside atmosphere using the shortest
duct run possible
– Use cylindrical ducting whenever possible
Positioning the rangehood
Installation heights
– Over gas and electric cookers,
Esatto
recommends our rangehoods to be mounted
at a height of between 600-800mm above the
cooking surface.
– Electric cooktops must have a minimum height of
600mm from the underside of the rangehood to the
cooktop face.
– Gas cooktops must have a minimum of 650mm from
the burner to the underside of the rangedhood.
– It is not recommended to install the rangehood
outside or over open flame grillers or barbecues.
Installing the rangehood
See illustration below
– Once you’ve determined your installation height,
drill 3 holes to install the mounting bracket (hook)
onto the wall ensuring that it’s secured in a level
position, Tighten the bracket with the screw plug
and screw (ST4mm X 30mm).
– When finished, line up the hood and hang onto the
wall bracket hook. (See pic A )
– Attach the extensible 150mm tube to the canopy.
Put the inside chimney with the outside chimney
together, ensure that the inner chimney piece can
move freely inside. Now attach the chimney to the
hood. When finished, fix the outside chimney to the
canopy, mark the hole and drill 2 holes, then tighten
the outside chimney bracket with screw plug and
screw (ST4mm X 30mm). (See pic B )
If you need the safety screws fixed into the hood,
please mark, drill and tighten the hood with screw
plug and screw (ST4mm X 30mm). Note, you will
need to remove the grease filters first. (See Pic C )
– Slide the inner chimney to adjust the inner chimney
height. When the height you required is reached,
mark it and accommodate the inner chimney bracket
with screw plug and screw (ST4mm X 30mm).When
finished, fix the inner chimney with the screws (4mm
X 8mm) to the inner chimney bracket . (See pic C )
Warning
Failure to install the screws or fixing device in
accordance with these instructions may result in
electrical hazards. The warning shall be in the same
part of the instructions that include details of how
to mount the equipment.
INSTALLATION INSTRUCTIONS
CONTINUED