background image

 

U

SER 

M

ANUAL

 

M

ARCH 

2017 

 

SolidRun Ltd  

 

www.solid-run.com

 Page 10 of 22 

 

 

7 HaMada Street, Yokne’am Illit, Israel 

 

 

Switch 1 

Switch 2 

Switch 3 

Switch 4 

Switch 5 

SPI 

Off 

Off 

Off 

On 

Off 

SD/eMMC 

Off 

Off 

On 

On 

On 

M.2 SSD 

On 

On 

On 

Off 

Off 

UART 

Off 

On 

Off 

Off 

On 

Table 1 Boot Selection Table 

For additional insights on operating system, please visit the 

Downloads

 section of our 

home page

Additional extensive resources are available in the 

Support

 section of our Wiki. 

 

4.4

 

M

ICRO

USB

 CONNECTIVITY 

(UART

 TO MICRO

USB) 

 

The ClearFog Base Single Board Computer has an FTDI 230x UART to USB bridge allowing convenient 
connection to the device console. This configuration is typically used by developers for debugging 
purposes (e.g. kernel or drivers). Such serial console connection is of USB-to-UART type. The 
connection speed should be set to 115200 bps. Further information is displayed on our wiki page with 
tags #

UART

 & #

serial

 & #

console

 

4.5

 

LED

S

 

 

There are multiple LEDs on the ClearFog Base Single Board Computer. These are indicating for 
example power on, connection and port activity. Ethernet port related LEDs are embedded in the 
RJ45 connectors, while the power indicator LED is located on the ClearFog Base Board. For further 
details, please refer to our 

wiki.solid-run.com

 pages. 

 

 

Figure 5 Location of LEDS on the ClearFog Base 

4.6

 

 

SIM

 CARD SLOT

/

S

 

It is possible to utilize a Cellular connection by inserting a SIM card into the SIM card slot. Please note 
that a GSM Cellular modem needs to be installed utilizing the M.2 2242 slot in order to exploit the 
cellular connection. 

Summary of Contents for ClearFog























Reviews: