background image

 10 

OPERATING THE UNIT USING THE CONTROL PANEL 

 

Air Conditioner Mode 

1)  Install the exhaust hose and window kit properly (see pages 7 & 8 ). 
2)  Plug the Power Cord into an electrical outlet. 
3)  Turn on the unit by pressing the 

POWER 

button on the control panel. 

4)  Press the Mode button until the led of AIR CONDITIONER light up on the control panel display. 
5) Press the 

 

or 

 buttons until the desired room temperature appears on the control panel display.  The 

temperature ranges from 61

°

F - 88 

°

F (16 

°

C - 31 

°

C). 

6)  Select the desired fan speed by pressing the 

FAN 

button. 

 

NOTE: 

During hot days, the unit will cool the room most efficiently by setting the temperature at the lowest 

setting and the fan speed on high. Reducing the length of the exhaust duct, insulating the exhaust hose and 
window kit, and keeping direct sunlight to a minimum will also improve the cooling efficiency.  
 

NOTE

: When the unit is running on cooling mode, the exhaust hose 

is

 required and must be vented outside 

using the supplied window kit.  
 

 
Dehumidifier Mode 

1)  Install the exhaust hose and window kit properly (see pages 7 & 8 ). 
2)  Plug the Power Cord into an electrical outlet. 
3)  Turn on the unit by pressing the 

POWER 

Button on the control panel. 

4) Press the 

MODE 

button until the led of  DEHUMIDIFIER light up on the control panel display.  

5)  change the direction of the air flow manually adjust the horizontal louvers up or down. 
 

NOTE:  

The unit operates at low fan speed during dehumidifier mode.  The unit cools room slightly during 

while dehumidifying. Keep the windows and doors closed to aid the effectiveness of the unit as it removes 
moisture from the room. 
 

NOTE:  

When the unit is running on dehumidifier mode, the exhaust hose 

is

 required and must be vented 

outside using the supplied window kit. The unit will not perform in dehumidifier mode when the room tem-
perature is lower than 61

°

F .  

 

 
 

Compressor Indicator 

The COMPRESSOR 

LED

 will light up on the control panel display when the compressor turns on. The 

LED

 of 

COMPRESSOR will turn off when the compressor shuts off. 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for HCB-P11-A















Reviews: