manualshive.com logo in svg

Solera 434729, Installation And Owner'S Manual

Share
Download
Solera 434729 Installation And Owner'S Manual Download Page 7

7

lci1.com      

 

574-537-8900    

 

Rev:07.19.18

Solera

®

 

Power Awning 18V

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0001260

10. 

Cut the cable ties, locate the switch on the side of the 

arm and open the awning halfway out.

11. 

Remove the wire cover to expose the fastening points.

12. 

Install the remaining two #14 x 1 

1/4

” screws at any of 

the three locations shown in the center of the support arm 

(Fig.7)

.

13. 

Repeat this process for the other side of the awning 

assembly.

Fig.7 

possible

fastener

locations

Securing The Fabric

1. 

Extend and retract the awning several times to make 

sure the fabric is square on the roll tube.

2. 

On both ends, secure the fabric in the awning rail no 

more than 1” inside the edge of the fabric using a #6 x 

1/2

” 

hex head screw 

(Fig.8)

.

3. 

Install the screw down through the awning rail into the 

fabric and the polycord.

Fig.8 

awning rail

fabric stitching

1”

Summary of Contents for 434729













Reviews:

No comments

Brands by name

Popular brands

Load more brands