Quick Installation Guide
—— Triple Power Lithium-ion Battery
100 Ah
Packing List
I
Note: The Quick Installation Guide briefly describes required installation steps. If you have any question,
please
refer to the User
Manual
delivered
with the BMS for
details
.
BMS (TBMS-MCS60060):
One
Battery Module (TP-HS50×1):
Wall Bracket x 2
Expansion Sleeve
x
4
Tapping Screw
x
2
Shim Ring
x 2
M5*10 Phillips-head Screw x 10
All Accessories Required for Two Installation Modes
Adjustment Screw
x 2
Base Support
x 2
Transverse Plate
x 1
Expansion Bolt
x 6
M5*8 Countersunk Head Screw
x 4
M5*20 Countersunk Screw
x 6
P
laten
(3 holes)
x 2
P
laten
(2 holes)
x 2
II
Installation Prerequisites
Ensure that the installation location meets the following conditions:
The building is designed to withstand earthquakes
The location is far
the sea to avoid salt water and humidity, over 3280
.
84 ft/1000 m
from
The floor is flat and level
There are no flammable or explosive materials, at a minimum of 2
.
95 ft/0.9 m
The ambience is shady and cool, away from heat and direct sunlight
The temperature and humidity remain at a constant level
There is minimal dust and dirt in area
There are no corrosive gases present, including ammonia and acid vapor
Where charging and discharging, the ambient temperature ranges from 32
℉/
0°C to 113
℉/
45°C
ŸŸŸŸŸŸŸŸŸŸ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
In practice, the requirements of battery installation may be different due to enviroment and locations.
In that case, follow up the exact requirements of the local laws and standards.
The
Triple Power
battery module is rated at
IP65
and thus can be installed outdoors as well as indoors. However, if installed outdoors, the
battery pack shall not be exposed to direct sunlight and moisture.
Note!
If the ambient temperature exceeds the operating range, the battery pack will stop running to protect itself.
The optimal temperature range for operation is 14
℉
/-10°C to 122
℉
/50°C
. Frequent exposure to harsh temperatures may deteriorate its
performance and lifetime.
Note!
For the first installation, the interval among manufacture dates of battery modules shall not exceed 3 months.
Note!
III
Overview
(
Floor
Mounting
)
Scheme A
Scheme B
Scheme C
BMS
Battery
Battery
Base
Distance from the equipment:
To left side:
≥
11.81 in./300 mm
To right side:
≥
11.81 in./300 mm
BMS
Battery
Battery
Base
31.81 in./808 mm
2 * Wall Bracket
2 * Expansion Bolt
2 * Tapping Screw
2 * Gasket
14 * M5*10 Screws
2 * Platen (3 holes)
4 * Platen (2 holes)
Distance from the equipment:
To left side:
≥
11.81 in./300 mm
To right side:
≥
11.81 in./300 mm
4 * Wall Bracket
4 * Expansion Bolt
4 * Tapping Screw
4 * Gasket
20 * M5*10 Screw
4 * Platen (3 holes)
4 * Platen (2 holes)
BMS
Battery
Battery
Base
Battery
43.62 in./1,108 mm
BMS
Battery
Battery
Base
Battery
Distance from the equipment:
To left side:
≥
11.81 in./300 mm
To right side:
≥
11.81 in./300 mm
4 * Wall Bracket
4 * Expansion Bolt
4 * Tapping Screw
4 * Gasket
24 * M5*10 Screw
4 * Platen (3 holes)
6 * Platen (2 holes)
BMS
Battery
Battery
Base
Battery
Battery
55.43 in./1,408 mm
BMS
Battery
Battery
Base
Battery
Battery
Steps (Floor Mounting)
IV
Step 2: Locate the Base 1.57 in./40 mm away from the
wall, accurately mark the location of the Base on both
sides with a pen.
Step 1: Place Base.
(1) Remove the dust cover.
(2) Insert M8*85 screws from the bottom of Base, to
ensure that the Base is even.
(a) Use a spirit level to measure the sides of the Base to ensure they are even.
(b) If not, please adjust the Adjustment Screws by a torque wrench being to ensure that the Base
is even.
Note!
Step 3: Place Battery Module on the Base.
(1) Remove the top and bottom dust covers.
(2) Place the Battery Module on the Base.
Please reserve enough distance from the equipment to the ceiling/ground for capacity expansion.
Take Scheme C as an example.
Right View
1.57 in
40 mm
1.57 in.
40 mm
Mark
(3) Fix the Platen (2 holes) using M5 * 10 Phillips-head screw, and
secure M5*10 screws at both sides (Torque: 1.0 N·m).
Step 4: Place two Battery Modules in turn, and secure both left and
right sides using M5*10 countersunk screws (Tighten torque: 1.0
N·m). Refer to the Step 2 (3).
Please
secure Platen and M5*10 screws immediately after placing a
Battery Module.
Platen (2 holes)
×
2
M5*10 Screw
×
4
1.0 N·m
Step 3 (3)
Platen (2 holes)
×
4
M5*10 Screw
×
8
1.0 N·m
Step 5:
(1) Attach M5 * 10 screw to Wall Bracket but be sure not to tighten;
(2) Place Wall Bracket to the wall, align its holes to the holes on the Battery,
and use a spirit level to ensure it's even;
(3) Accurately mark the location of the Wall Bracket on both sides;
(4) Circle along the inner ring of the holes;
(5) Remove the Wall Bracket, and then drill the two holes (at least 3.54 in./90
mm) by a Drill (
φ
0.39 in./10 mm).
Attach screw but not
tighten
Mark
Electric drill dust collector is recommended.
Note!
(1)
(2)
If the Base is shifted after placing a Battery Module, move it to its
original location according to the mark previously drawn.
Note!
Step 6: Place Expansion Bolts.
Step 7: Place the Wall Bracket on the wall where the mark is drawn
previously, and secure it using Tapping Screws and Gaskets.
32 in./812.80 mm
Tapping Screw × 2
Gasket × 2
Wall Bracket × 2
Attach screw but not
tighten
, and align the hole
location of battery
32 in./812.80 mm
Mark
Step 8: Place the fourth battery module.
Let the Platen
down
Step 9: Fix the Platen (3 holes), and tighten M5*10 screws on both sides
(Torque: 1.0 N·m).
Platen (3 holes)
×
2
M5*10 Screw
×
6
1.0 N·m
Step 11: Place BMS on the Battery Module.
(1) Remove the bottom dust cover.
Electric drill dust collector is recommended
.
Note!
Step 10:
(1) Attach M5 * 10 screw to Wall Bracket but be sure not to tighten;
(2) Place such Wall Bracket to the wall, align its holes to the holes on the
Battery Module, and use a spirit level
to ensure it's even;
(3) Accurately mark the location of the Wall Bracket on both sides with a pen;
(4) Circle along the inner ring of the holes;
(5) Remove the Wall Bracket, and drill two holes (at least 3.54 in/90 mm) by a
Drill (
φ
0.39 in./10 mm);
(6) Place Expansion Bolts;
(7) Secure Wall Brackets. Refer to the Steps 5, 6, 7 and 8.
32 in./812.80 mm
Step 5
,
6, 7 and 8
Let the Platen
down
Step 9
Platen (3 holes)
×
2
M5*10 Screw
×
6
1.0 N·m
Tapping Screw × 2
Gasket × 2
Wall Bracket × 2
32 in/81
2.80 mm
Mark
(2) Place BMS, fix the Platen (3 holes) on
both sides, and then tighten M5*10 screws
(Torque: 1.0 N·m). Refer to Step 9.
Documentation x 1
BMS
Battery
Battery
Base
BMS
Battery
Battery
Base
Battery
BMS
Battery
Battery
Base
Battery
Battery
The holes on BMS is for secure inverter. For details, please refer to A1-
ESS-G2 User Manual.
Note!
32 in/812.80 mm
BMS x 1
User Manual x 1
Battery Module x 1
Expansion Bolt x 4
Wall Bracket x 2
Gasket x 2
Platen (2 holes) x 2
Tapping Screw x 2 M5*10 Phillips-head Screw x 10
Platen (3 holes) x 2
Quick Installation Guide x 1
Base Support x 2
Expansion Screw x 6
Transverse Plate x 1
M5*8 Countersunk Head Screw x 4
M5*20 Countersunk Screw x 6
Adjustment Screw x 2
Self-tapping Screw x 6
Base for BAT50-G2 Battery:
Base x 1
Φ
0.39 in./10 mm
for Wall Bracket
≥
3.54 in./
90 mm
Safety
Instructions x 1
