manualshive.com logo in svg

SolarEdge SE10KUS, Installation Manual

Share
Download
SolarEdge SE10KUS Installation Manual Download Page 40

NOTE

When mounting an inverter  on an uneven surface, you may use  spacers/

washers behind the top mounting hole of the bracket. Depending on the

angle, use the appropriate size and number of spacers so that the bracket is

perpendicular to the ground. Recommended: a stainless steel 3/4" long screw,

with a 1/4" socket button head , two jam nuts and three washers.

5.  Hang the inverter on the bracket (see  

Figure 17): Lift the inverter from the sides, or

hold it at the top and bottom of the inverter to lift the unit into place. Do not lift

holding the Safety SwitchDC Safety Unit as it may be damaged.

6.  Align the two indentations in the inverter enclosure with the two triangular

mounting tabs of the bracket, and lower the inverter until it rests on the bracket

evenly.

Figure 17: Hanging the inverter on the bracket

7.  Secure the Safety Switch bracket to the wall:

8.  For inverters with Safety Switch -  secure the Safety Switch bracket to the wall:

Mark the location of the bracket screw for the Safety Switch and drill the

hole.

Chapter 3: Installing the Inverter     

39

Three

 

Phase

 

System

 

Installation

 

Guide

 

MAN-01-00527-1.

2

Summary of Contents for SE10KUS






































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands