Solare Datensysteme Solar-Log Components Connection Manual Download Page 396 | Manualshive

Page: 396 / 506

background image

396

Zucchetti Centro Sistemi S.p.a

112

Zucchetti Centro Sistemi S.p.a

112.1

Azzuro

Termination

Addressing

Interface

Yes

Yes

RS485

Selection available under SofarSolar

Supported models (Wiring via RJ45) (as of firmware 4.1.1):

•

Azzuro 4.4KTL, 5.5KTL, 6.6KTL, 8.8KTL, 11KTL, 12KTL

•

Azzuro 10000TL, 15000TL, 17000TL, 20000TL

•

Azzuro 30000TL, 33000TL, 40000TL

•

Azzuro 50000TL, 60000TL, 70000TL

Supported models (Wiring via RS485 pin block) (as of firmware 4.1.1):

•

Azzuro 1100TL, 1600TL, 2200TL, 2700TL, 3000TL

•

Azzuro 3000TLM, 3680TLM, 4000TLM, 4600TLM, 5000TLM, 6000TLM

•

Azzuro 3KTLM, 3.6KTLM, 4KTLM, 4.6KTLM, 5KTLM, 6KTLM

Overview

•

Integrated interface.

•

Where to connect: RS485 pin block, inside the inverter.

•

Where to connect: RJ45 socket inside the inverter.

•

2-pin wiring.

•

The communication address has to be assigned.

•

Installation steps:

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™.

•

Connect the inverters to each other according to the inverter instructions.

Connect inverters to the Solar-Log™ (via RJ45)

The wiring is done using a

•

self-made RS485 data cable with RJ45 plug and terminal block connector.

Procedure

1. Open the inverter as shown in the inverter‘s instructions.
2. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

RJ45 inverter

Terminal

Pin

►

1 Data+

►

2 RS485 A (+) (Orange)

►

4 Data-

►

1 RS485 B (-) (White and Orange)

«
...
394
395
396
397
398
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: Omega Pages: 7

Brand: INFRA-E-MOTION Pages: 15

Brand: ICP DAS USA Pages: 131

Brand: Thermomax Pages: 32

Brand: Seeed Pages: 51

Brand: A&D Pages: 2

Brand: Campbell Pages: 212

Brand: Tamprecords Pages: 6

BLUEPIRAT Rapid Series

Brand: Magna Pages: 67

Brand: Spotsee Pages: 115

Brand: Kipp & Zonen Pages: 60

Brand: Brodie Pages: 94

Brand: Kipp & Zonen Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands