Solare Datensysteme Solar-Log Components Connection Manual Download Page 163 | Manualshive

Page: 163 / 506

background image

163

Hyundai

44.2

Hyundai HPC-250HT-E

Termination

Addressing

Interface

Yes

Yes

RS485

Overview

•

Integrated interface

•

Where to connect: 20 pin connection strip on the outside of the inverter at the top edge of the i-8142iW mo-
dule

•

2-pin wiring

•

Communication address must be allocated

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

•

Allocate communication address

Connect inverters to the Solar-Log™

The wiring is done using a

•

ready-made data cable (optional extra; not supplied)

or

•

self-made, shielded 2 wire data cable and terminal block connector.

Caution

Risk of damage to the unit!
The Solar-Log™ also has an RJ45 socket, which must never be connected to the RJ45 socket on the
inverter.

►

Only connect inverters via the RS485/422 Solar-Log™ interface(s).

Procedure

1. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Inverter terminal strip

Terminal

Terminal

►

1

►

D1+/TxD1+

►

4

►

D1-/TxD1-

2. If no further inverter is connected, terminate the inverter according to the instructions for the inverter.
3. Insert the terminal block connector into the Solar-Log™ RS485 socket.

Connect the inverters to each other

•

Connect using a 2 wire, shielded data cable

•

Where to connect: 20 pin connection strip on the inverter at the top edge of the i-8142iW module.

«
...
161
162
163
164
165
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: VOLTCRAFT Pages: 8

Brand: Ronds Pages: 15

Brand: Leica Pages: 48

Brand: Elma Instruments Pages: 36

Brand: T&D Pages: 2

Brand: Oakton Pages: 219

Brand: Sentek Pages: 58

Brand: Sparr Pages: 8

Brand: Wavetronix Pages: 3

Brand: Racepak Pages: 24

Brand: visilab Pages: 3

Brand: Dahua Pages: 24

GridVis Collector

Brand: janitza Pages: 116

ULTRASONIC Portable

Brand: Calypso Instruments Pages: 13

Brand: METER Pages: 2

Brand: Geco Pages: 12

Brand: GE Pages: 145

Brand: Hanna Instruments Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands