manualshive.com logo in svg

Solair J18HA-A, Installation Instructions Manual

Share
Download
Solair J18HA-A Installation Instructions Manual Download Page 26

Manual 2100-660 

Page 

26 of 32

FIGURE 11

Fan Blade Setting

TABLE 6

Fan Blade Dimension

REMOVAL OF FAN SHROUD

1.  Disconnect all power to the unit.

2.  Remove the screws holding both grilles, one on 

each side of unit, and remove grilles.

3.  Remove nine screws holding fan shroud to 

condenser and bottom.

4.  Unwire condenser fan motor.

5.  Slide complete motor, fan blade and shroud 

assembly out the left side of the unit.

6.  Service motor/fan as needed.

7.  Reverse steps to reinstall.

R-410A REFRIGERANT CHARGE

This unit was charged at the factory with the quantity 
of refrigerant listed on the serial plate.  AHRI capacity 
and efficiency ratings were determined by testing with 
this refrigerant charge quantity.

The following pressure tables show nominal 
pressures for the units.  Since many installation 
specific situations can affect the pressure readings, 
this information should only be used by certified 
technicians as a guide for evaluating proper system 
performance.  They shall not be used to adjust charge.  
If charge is in doubt, reclaim, evacuate and recharge 
the unit to the serial plate charge

.

"A"

AIRFLOW

MIS-1724

Model

Dimension

A

J18HA
J24HA

1.00"

J30HA
J36HA

1.25"

J42HA
J48HA
J60HA

1.75"

FAN BLADE SETTING DIMENSIONS

The correct fan blade setting for proper air delivery 
across the outdoor coil is shown in Figure 11.  Refer to 
Table 6 for unit specific dimension.

Any service work requiring removal or adjustment in the 
fan and/or motor area will require that the dimensions 
below be checked and blade adjusted in or out on the 
motor shaft accordingly.

Summary of Contents for J18HA-A

































Reviews:

No comments

Brands by name

Popular brands

Load more brands