Software House iSTAR PRO Quick Start Installation Manual Download | Manualshive

Page: 16 / 20

background image

ACM - Access Control Module(s)

16

Inputs

The wiring of supervised inputs is shown in the next two figures. Note that the resistor
network is different for NO and NC switches.

Normally Open (NO) Wiring

Normally Closed (NC) Wiring

NOTE

To comply with UL requirements, use shielded, minimum 22 AWG stranded,
twisted pair cable for monitor points, DSMs, and R

EX

s. Use Belde

n

9462 or

equivalent.

Outputs

The outputs are dry contact Class C relays that are rated at 5 amps. Since they are dry
contact, the technician must supply external power. The following two examples show
an electric strike wired as both Fail Secure and Fail Safe.

«
...
14
15
16
17
18
...
»

Summary of Contents for iSTAR PRO





















Reviews:

No comments

Related manuals for iSTAR PRO

Concord express

Brand: GE Pages: 3

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Brand: fakro Pages: 16

Brand: e-BLEACH Pages: 24

Brand: Vacon Pages: 6

Brand: Vacon Pages: 24

Brand: Vacon Pages: 30

Brand: Vacon Pages: 81

Brand: Vacon Pages: 100

Brand: Bartlett Pages: 7

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: Parker Pages: 4

Brand: Casambi Pages: 2

Brand: WAGNER Pages: 128

Brand: IMG STAGELINE Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands