Softing WireXpert 4500 Fiber MPO User Manual Download Page 5

Page: 5 / 41

Introduction

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

WARNING

indicates a potentially hazardous situation which, if not avoided, could result in

death or serious injury.

DANGER

indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury. This signal word is to be limited to the most extreme situations.

1.3

Intended use

WireXpert series has been designed for use in factory, process and building control. The unit must not

be used in explosion hazard areas. The permissible ambient conditions given in the Technical Data must

be complied with.

The faultless and safe operation of the product requires proper transport, proper storage and

installation, and expert operation and maintenance in accordance with the manual.

1.4

About this document

Read this manual before starting

For damages due to improper connection, implementation or operation Softing refuses

any liability according to our existing warranty obligations.

1.4.1

Document history

Document version

Modifications compared to previous version

201702

Firmware update to v7.3

201811

Firmware update to v8.0

Summary of Contents for WireXpert 4500 Fiber MPO










































Search results

Summary of Contents for WireXpert 4500 Fiber MPO

Reviews:

Related manuals for WireXpert 4500 Fiber MPO

Brands by name

Popular brands

Softing WireXpert 4500 Fiber MPO, User Manual

Search results

Summary of Contents for WireXpert 4500 Fiber MPO

Reviews:

Related manuals for WireXpert 4500 Fiber MPO

Brands by name

Popular brands