Sofar solar 1.1K-3.3KTL-G3 User Manual Download Page 47

Page: 47 / 73

SOFAR 1.1K~3.3KTL-G3

User manual

- 42 -

5. Commissioning of inverter

5.1. Safety inspection before commissioning

Ensure that DC and AC voltages are within the acceptable range

of the inverter.

Attention

5.2. Start inverter

Step 1:

Turn ON the DC switch.(optional)

Step 2:

Turn ON the AC circuit breaker.

When the DC power generated by the solar array is adequate, the SOFAR

1.1K~3.3KTL-G3inverter will start automatically. Screen showing

“

normal

”

indicates correct operation.

NOTE:

Choose the correct country code. (refer to section 6.3 of this manual)

Notice:

Different distribution network operators in different countries have different

requirements regarding grid connections of PV grid connected inverters.

Therefore, it's very important to make sure that you have selected the correct

country code according to requirements of local authority.Please consult qualified
electrical engineer or personnel from electrical safety authorities about this.

Shenzhen SOFARSOLAR Co., Ltd. is not responsible for any consequences

arising out of incorrect country code selection.

If the inverter indicates any fault, please refer to Section 7.1 of this manual

—

trouble shooting for help.

NOTE:The inverter can monitor the power grid in real time,The protection can

be realized when the power grid is abnormal, so that the inverter is separated from
the power grid.

Summary of Contents for 1.1K-3.3KTL-G3










































































Search results

Summary of Contents for 1.1K-3.3KTL-G3

Reviews:

Related manuals for 1.1K-3.3KTL-G3

Brands by name

Popular brands

Sofar solar 1.1K-3.3KTL-G3, User Manual

Search results

Summary of Contents for 1.1K-3.3KTL-G3

Reviews:

Related manuals for 1.1K-3.3KTL-G3

Brands by name

Popular brands