Sodex Sport S30161 Assembly Instructions Manual Download Page 1

 1

 

 1

 

 

DETAILS

 

SODEX INTERNATIONAL

 

18 rue de l

avenir –

 

Bât. 224

 

14650 CARPIQUET

 

Tel: + 33 (0) 2.31.53.78.70

 

Email: [email protected]

 

 

DESCRIPTION

 

Steel structure 

 

Powder coated

 

 

 

CONFORM

 

European norm

 

 

NF EN 1271

 

 

 

ASSEMBLY INSTRUCTION

 

VOLLEYBALL POSTS Ø90, 

 

WINCH TENSION

 

PRODUCT REF

:

 

S30161

 

PAIR

 

TIME

 

 

The assemblage time of the volleyball posts is estimated at 20 minutes, with 1 person 

 

MAINTENANCE

 

The equipment has to be regularly maintained by the owner. It is advised to:

 

 

-

 Check every week that all the screws are correctly tightened

 

-

 Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufacturer.

 

-

 Replace all damaged or missing parts with a spare part recommended by the manufacturer. 

 

-

 Clean the product by using dishwasher soap, clean water, and soft cloth.

 

It is advised to carry out this cleaning once or twice a year, or even more regularly according to the environmental 

conditions (saline environment, 

…).

If the forecast planned a bad weather (strong wind,

…), 

the goal should be remo-

ved from the sheaths and put on the ground. 

 

 

WARRANTY

 

One full year parts and labor guarantee. Every claim regarding condition of the delivered equipment has to be done 

within the legal period of the reception of the material. The warranty will not apply to:     

 

-

    all degradation during the transport.     

 

-

    all degradation due to use differing from which was intended.

 

-

    all degradation due to poor maintenance.     

 

-

    any defect claimed after the end of the legal period.     

 

-

    any damaged due to a faulty installation and assembly of the module

 

Summary of Contents for S30161












Reviews: