socomec ISOM K-20 Installation And Operating Manual Download Page 15 | Manualshive

Page: 15 / 22

background image

15

EN

ISOM K-20 - 551805A - SOCOMEC

8.1.2.2. Insulation

The "Insulation Profiles" screen defines the general settings of the device:
Choosing the profile is an easy way to support the measurement algorithm on the intended application, with improved
filtering/measurement times.
You can choose between 3 profiles:

• Custom
• Distribution
• Control/command

«
...
13
14
15
16
17
...
»

Summary of Contents for ISOM K-20























Reviews:

No comments

Related manuals for ISOM K-20

Brand: UEi Pages: 4

Brand: DayTronic Pages: 54

Brand: Bacharach Pages: 2

Brand: Bachmann Pages: 33

Brand: Candela Pages: 4

Brand: M & I Instruments Pages: 2

Brand: Nady Audio Pages: 2

Brand: Waterproof Pages: 10

Brand: Ocean Optics Pages: 43

Brand: Ocean Technology Systems Pages: 12

Brand: Ocean Reef Pages: 24

Brand: R&S Pages: 733

Brand: R&S Pages: 369

Brand: YOSensi Pages: 3

Brand: Keeler Pages: 54

Brand: Dewetron Pages: 24

Brand: SKF Pages: 12

Brand: Van Walt Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands