background image

9

Transporting the Mower 

During normal operation, the blade reel will turn anytime the 

mower's front wheels are turning. To safely move the mower 

from one location to another without the blade reel turning, 

simply pivot the handle over the reel and push the mower from 

the opposite side. Pushing the mower in this manner (transport 

mode) prohibits the blade reel from turning (Fig. 10).

Care and Maintenance 

1.  Minimum care is required to ensure smooth operation of 

your mower.

2.  To avoid damage to the mower or cutting blades, keep the 

area to be mowed free from debris.

3.  For best results, regularly apply lubricant to the mower’s 

cutting surfaces, cutting reel axle shaft, and wheels.

Sharpening the Cutting Blades

1.  Spread a thin layer of lapping compound on the front edge 

of the reel blades.

2. 

Adjust the cutting bar so that the blade has light but firm 

contact across the full width of the bar. 

m

CAUTION!

 Do not overtighten the adjusting screws, as 

this could damage the cutting bar. Tighten both screws during 

final adjustment.

3.  Turn the reel blades until the front edge of the cutting bar 

blade is polished.

m

WARNING!

 Clean any grinding compound or debris 

from the cutting bar blade, reel blade, pinions, and pawls.
NOTE: Use industrial or valve lapping compound between 100 

and 240 grit.
NOTE: 

Lubricate the axle and pinion with a light film of wheel 

bearing grease.

Cleaning and Storage

1.  Clean the exterior of the machine thoroughly using a soft 

brush and cloth before storing. Do not use water, solvents, 

or polishes.

2.  Turn the mower on its side to clean the blade area.

m

WARNING!

 Do not place your hands inside or near the 

cutting area. If grass cuttings are compacted in the blade area, 

remove them using a wood or plastic cleaning tool appropriate 

for blade cleaning.

3.  Store the mower in a dry place. Do not place other objects 

on top of the mower during storage.

Maintenance Tips

Reel mowers are relatively low maintenance. For consistent 

cutting, follow the below instructions:

•  Always keep the cutting bar properly adjusted. Refer to the 

instruction manual for further directions.

•  Regularly clean and lubricate cutting edges with light spray oil.

IMPORTANT!

 Reel mowers have difficulty cutting tall weeds, 

such as dandelions, and will often bend, rather than cut, such 

weeds. Cut often to prevent this.

Service and Support

If your Sun Joe

®

 manual reel mower requires service or 

maintenance, please call the Snow Joe

®

 + Sun Joe

®

 customer 

service center at 1-866-SNOWJOE (1-866-766-9563).

Model and Serial Numbers 

When contacting the company or reordering parts, you will 

need to provide the model and serial numbers of your product. 

These are found on the decal affixed to the housing of your 

reel mower. Copy these numbers into the space provided 

below.

R

Handle

Fig. 10

Record the following numbers from the housing or handle of your  

new product:

M  J    5   0   4   M   -    R  M

Model #:

Serial #:

Summary of Contents for SUNJOE MJ504M-RM













Reviews: