background image

15

2. 

Take off the bar sheath.

3.  Make sure the guide bar is not touching the ground or 

any other object.

4. 

Hold the pole chain saw firmly with both hands.

5.  To turn the tool ON, push and hold the safety lock switch 

on the top of the handle grip with your thumb and then 

squeeze the trigger switch with your fingers. Once the 

tool is running, you can release the safety lock switch and 

proceed with operation (Fig. 19).

 NOTE: Do not press the trigger switch until you are ready 

to make a cut.

6.  To turn the tool OFF, release the trigger switch.
7.  Lift the push lock button and pull out the battery (Fig. 14).

Adjusting the Telescoping Pole

1. 

Turn off the trigger switch.

2.  Unclip the cam-lock to release the pole (Fig. 20).

3.  Extend the pole to the desired length (Fig. 21). 
  NOTE: Push poles toward each other to shorten the pole 

or pull them away from each other to lengthen the pole. 

Only extend the pole to the minimum length required to 

reach the limb to be cut.

4.  Lock the pole in position by closing the cam-lock (Fig. 22), 

and ensure that the pole is secure. If the pole telescopes 

when the cam-lock is closed, the nut may need tightening.

m

WARNING! 

Failure to lock the telescopic pole cam-lock 

as directed could result in personal injury.

Tightening the Bolt

The retaining bolt may need tightening to secure the telescopic 

pole in place. 

1.  Unclip the cam-lock. Using a hex key wrench, tighten the 

cam-lock nut, then close the cam-lock. Ensure that the 

pole is secure. The wrench may be required to loosen the 

cam-lock nut if you need to adjust the pole to a different 

height (Fig. 23).

Fig. 19

Safety lock switch

Trigger switch

Fig. 20

Cam-lock

Fig. 21

Telescopic pole

Fig. 22

Cam-lock

Fig. 23

Hex key wrench

Cam-lock nut

Summary of Contents for Sunjoe iON8PS2

























Reviews: