SNOWJOE SJ623E-RM Operator'S Manual Download Page 6

5

Know Your Electric Snow Thrower

Read the owner’s manual and safety rules carefully before operating your electric snow thrower. Compare the illustration  

below to the actual unit in order to familiarize yourself with the location of the various controls and adjustments. Save this 

 

manual for future reference.

Technical Data

Rated Voltage 

120 V ~ 60 Hz

Power 

15 A

Light (Model SJ623E-RM only) 

12 V, 20 W halogen 

No Load Speed 

2450 rpm

Clearing Width 

18 in. (46 cm)

Clearing Depth 

10 in. (25.4 cm)

Throw Distance (max) 

25 ft (7.6 m)

Plowing Capacity (max) 

720 lbs/min (327 kg/min) 

Directional Control 

180º adjustable chute

Rotor 

4 rubber-tipped steel blades

Weight (SJ622E-RM) 

32.4 lbs (14.7 kg) 

Weight (SJ623E-RM with light) 

33.7 lbs (15.3 kg) 

1.  Handle bar
2.  ON/OFF switch lever
3.  Safety switch button
4.  Cable restraint holder
5.  Middle frame
6.  Lower frame
7.  Wheels (located at the back of the machine)
8. 

Polarized cable plug

9.  Upper frame

10. Upper chute crank
11. 

Joint fixing T-Bolt and knob (4 pcs)

12. Lower chute crank
13.

 Chute deflector

14. Discharge chute
15. Main cover
16. Rubber-tipped steel plates
17. Auger
18. Scraper bar
19. Chute clean-out tool

Figure 1-1 (Model SJ622E-RM)

Figure 1-2 (Model SJ623E-RM with 20 W Halogen Light)

Light

Light Switch

 

 

1
2
3

11

12

13

15

16

18

17

14

10

8
9

4
5

6

7

19

Summary of Contents for SJ623E-RM


















Reviews: