background image

23

SNOW JOE

®

 + SUN JOE

®

 REFURBISHED GOODS WARRANTY

GENERAL CONDITIONS: 

Snow Joe

®

 + Sun Joe

®

 operating under Snow Joe

®

, LLC warrants 

this refurbished product to the original purchaser for 90 days 

against defects in material or workmanship when used for normal 

residential purposes.  If a replacement part or product is needed, 

it will be sent free of charge to the original purchaser except as 

noted below.
The duration of this warranty applies only if the product is put to 

personal use around the household. It is the owner’s responsibility 

to correctly perform all maintenance and minor adjustments 

explained in the owner’s manual.

HOW TO OBTAIN YOUR REPLACEMENT PART OR PRODUCT:

To obtain a replacement part or product, please visit 

 

snowjoe.com/help or email us at [email protected] for 

instructions. Please be sure to register your unit beforehand 

to speed up this process. Certain products may require a serial 

number,  typically  found  on  the  decal  affixed  to  the  housing 

or guard of your product. All products require a valid proof  

of purchase.

EXCLUSIONS:

•  Wearing  parts  like  belts,  augers,  chains  and  tines  are 

not covered under this warranty. Wearing parts can be 

purchased at snowjoe.com or by calling 

1-866-SNOWJOE 

 

(1-866-766-9563).

•  Batteries  are  covered  in  full  for  90-days  from  the  date  of 

purchase. 

Snow Joe

®

 + Sun Joe

®

 may from time to time change the design of 

its products. Nothing contained in this warranty shall be construed 

as obligating Snow Joe

®

 + Sun Joe

®

 to incorporate such design 

changes into previously manufactured products, nor shall such 

changes be construed as an admission that previous designs 

were defective.
This warranty is intended to cover product defects only. 

 

Snow Joe

®

, LLC is not liable for indirect, incidental or 

 

consequential damages in connection with the use or misuse of 

the Snow Joe

®

 + Sun Joe

®

 products covered by this warranty. 

This warranty does not cover any cost or expense incurred  

by the purchaser in providing substitute equipment or service 

during reasonable periods of malfunction or non-use of this product 

while waiting for a replacement part or unit under this warranty. 

Some states do not allow exclusions of incidental or consequential 

damages so the above exclusions may not apply in all states. This 

warranty may give you specific legal rights in your state.

HOW TO REACH US:

We’re here to help Monday through Friday from 9AM to 7PM EST  

and  Saturday  and  Sunday  9AM  to  4PM.  You  can  reach  us  at 

1-866-SNOWJOE (1 866-766-9563), online at snowjoe/com, via 

email at [email protected] or tweet us @snowjoe.

EXPORTS:

Customers who have purchased Snow Joe

®

 + Sun Joe

®

  

products exported from the United States and Canada should 

contact their Snow Joe

®

 + Sun Joe

®

 distributor (dealer) to obtain 

information applicable to your country, province or state. If for 

any  reason,  you  are  not  satisfied  with  the  distributor’s  service, 

or  if  you  have  difficulty  obtaining  warranty  information,  contact 

your Snow Joe

®

 + Sun Joe

®

 seller. If in the event your efforts are 

unsatisfactory, please reach out to us directly.

Summary of Contents for POWERJOE 24V-PS1-RM

























Reviews: