14
Maintenance
To order genuine replacement parts or accessories for the
Snow Joe
®
24V-X2-20SB-CT-RM cordless snow blower, please
visit snowjoe.com or contact the Snow Joe
®
+ Sun Joe
®
customer service center at 1-866-SNOWJOE
(1-866-766-9563).
m
WARNING!
Make sure the unit is off and remove the
batteries before performing any maintenance tasks on your
snow blower.
Lifetime Lubrication (Motor + Auger)
Lubrication is not necessary and may damage the unit.
The snow blower is lubricated for lifetime use at the factory
before shipment.
General Maintenance Tips
m
WARNING!
Always switch the product off, remove
the batteries, and let the product cool completely before
inspecting, cleaning, or performing any other maintenance
task.
m
WARNING!
Only perform the repairs and maintenance
work described in this manual. Any other work must be
performed by a qualified technician.
1. Do not attempt to repair the machine unless you have the
proper tools and instructions for disassembly and repair of
the machine.
2. Check bolts and screws at frequent intervals for proper
tightness to ensure that the equipment is in safe working
condition.
3. After each snow removal session, run the snow blower
for a few minutes to prevent the collector/impeller from
freezing. Shut off the motor, wait for all revolving parts to
stop completely, and wipe residual ice and snow off the
unit. Rotate the chute deflector by the chute control crank
several times to remove any excess snow.
Replacing the Scraper Bar
IMPORTANT: Only use original replacement parts specified for
this snow blower.
You can purchase a replacement scraper bar (Model
24V-X2-20SB-SCRPR) and other genuine replacement parts
by visiting us online at snowjoe.com or calling our toll-free
customer service helpline at 1-866-SNOWJOE
(1-866-766-9563). The use of parts that do not meet the
original equipment specifications may lead to improper
performance of the snow blower, may compromise operator
safety and will void the manufacturer's warranty.
1. Turn off the snow blower, remove the batteries and wait
until the snow blower comes to complete standstill.
2. Open the two side panels by removing the 8 screws on
each side (Fig. 20).
2. Raise the snow blower as shown. Remove the 6 screws
used to attach the scraper bar, and remove the worn
scraper bar (Fig. 21).
3. Fit the new scraper bar in place, secure with the original 6
screws (Fig. 21).
4. Replace the 2 side panels and fix with the screws.
The snow blower is ready for use.
Replacing the Auger Blade
IMPORTANT: Only use original replacement parts specified for
this snow blower.
You can purchase a replacement auger blade (Model
24V-X2-20SB-AUGER) and other genuine replacement parts
by visiting us online at snowjoe.com or calling our toll-free
customer service helpline at 1-866-SNOWJOE
(1-866-766-9563). The use of parts that do not meet the
original equipment specifications may lead to improper
performance of the snow blower, may compromise operator
safety and will void the manufacturer's warranty.
NOTE: When replacing worn auger blade, pay close attention
to any different types of bolts and nuts and where they are
positioned. This will ensure that all parts are installed properly
and securely.
1. Turn off the snow blower, remove the batteries and wait
until the snow blower comes to complete standstill.
2. Follow the instructions above to remove the 2 side panels
(Fig. 20).
3. From the left side of the snow blower, remove the belt first.
Then use a hex wrench to loosen and remove the pulley
(Fig. 22).
Screws
Fig. 20
Side panel
Side panel
Screws
Fig. 21
Scraper bar
Summary of Contents for 24V-X2-20SB-CT-RM
Page 20: ...snowjoe com...
