background image

 

Owner’s Manual 

 

 

 

4

 

|

 

P a g e

 

SnowBear

®

 Tailgate Spreader (TGS-325) 

 

Personal Safety 

 

Remove  ignition  key  and  put  the  vehicle  in  park  or  in  gear  to  prevent  others  from  starting 
the vehicle during installation or service. 

 

Wear  only  snug-fitting  clothing  while  working  on  your  vehicle  or  spreader.  Do  not  wear 
dangling jewelry or neckties and secure long hair. 

 

Wear  safety  glasses  to  protect  your  eyes  from  dust,  dirt  &  debris  from  the  spreader, 
especially when in operation and close to spreader. Material is spread at significant velocity. 

 

Fire and Explosion 

  GASOLINE IS HIGHLY FLAMMABLE, VAPOURS  ARE EXPLOSIVE.

 Never smoke while 

working on vehicle. Keep all open flames and sources of ignition away from gasoline tank, 
lines  and  containers.  Wipe  up  any  spilled  gasoline  immediately.  Do  not  use  gasoline  to 
clean parts. Store gasoline only in approved containers away from sources of heat or flame. 

 

Ventilation 

  VEHICLE  EXHAUST  CONTAINS  LETHAL  FUMES.

  Breathing  these  fumes,  even  in  low 

concentrations, can cause illness or death. Never operate a vehicle or leave engine running 
while performing spreader maintenance in an enclosed area without venting the exhaust to 
the outside. 

 

Cell Phones 

 

A  driver's  first  responsibility  is  the  safe  operation  of  the  vehicle.  The  most  important  thing 
you  can  do  to  prevent  a  crash  is  to  avoid  distractions  and  pay  attention  to  the  road. Wait 
until  it  is  safe  to  operate  Mobile  Communication  Devices  such  as  cell  phones,  text 
messaging devices, pagers or two-way radios (ie. when vehicle is parked). 

 

 

 

Summary of Contents for TGS-325

















Reviews: