background image

Page 14

Operation Manual

SPECIFICATIONS

 

ITEM

M1230E

Platform Size

74cm x 96cm (

29 in. x 38 in.

)

Maximum Platform Capacity

227 kg (

500 lbs.

)

Maximum Number of Occupants

2 People indoors/1 person outdoors

Height

Working Height

5,6 m (

18 ft.

)

Maximum Platform Height

3,63 m (

11 ft. 11 in.

)

Minimum Platform Height

48,3 cm (

19 in.

)

Dimensions

Weight

780 kg (

1720 lbs.

)

Overall Width

76 cm (

30 in.

)

Overall Height

165 cm (

65 in.

)

Overall Length

1,36 m (

53.5 in.

)

Drive Speed

Platform Lowered

3,2 km/h (1.99 mph)

Platform Raised

0,65 km/h (0.46 mph)

Energy Source

24V battery pack

Four 220 ampere hour, 6 Volt batteries, min. wt. 26,3 kg (

58 lbs.)

 each 

4 HP DC electric motor

System Voltage

24 VDC

Battery Charger

20 AMP, 220 V AC 50Hz

Battery Duty Cycle

25% for 8 Hours

Hydraulic Reservoir Capacity

7,2 L (1.9 gal)

Maximum Hydraulic System Pressure

165 bar (2400 psi)

Hydraulic Fluid

Normal above 32° F [0° C]

ISO #46

Low Temp. below 32° F [0° C]

ISO #32

below 0° F [-17° C]

ISO #15

Lift System

One Single Stage Lift Cylinder

Drive Control

Proportional

Control System

Proportional Control Handle with Interlock, Selector Switch, Red 

Mushroom Emergency Stop Switches

Horizontal Drive

Dual Front Wheel

Tires

30,5 cm (12 in.) diameter solid rubber, Non-marking

Parking Brakes

Dual, Spring Applied, Hydraulic Release

Turning Radius

37 cm (14.5 in.) Inside

Maximum Gradeability

14º (25%)

Wheel Base

97,8 cm (

38.5 in.

)

Guardrails

1,10 m (

43 in.

)

Toeboard

152 mm (

6 in.

)

Max Chassis Inclination

1.5° Side to Side

2.0° Front to Back

Wheel loading

325kg per wheel / 716.5 lbs per wheel

Vibration of this machine does not exceed

2.5m/sec

2

Sound Pressure Level

68dB (A) at Control Station

Operating Temperature Range

-20° C to +50° C

*Specifications are subject to change without notice. Hot weather or heavy use may affect performance.
Refer to the Service Manual for complete parts and service information.
This machine meets or exceeds all applicable CE and GS machinery directive requirements.

Specifications

Summary of Contents for M1230E





















Reviews: