background image

Special fire fighting procedures:

Use wa ter to keep fire ex posed con tain ers cool. If
leak or spill has not ig nited, use wa ter spray to dis -
perse the va pors and to pro vide pro tec tion for per -
son nel at tempt ing to stop a leak. Wa ter spray may
be used to flush spills away from exposures.

Unusual fire and explosion hazards:

Prod ucts of com bus tion may con tain car bon mon -
ox ide,  car bon  di ox ide,  and  other  toxic  ma te ri als.

DO NOT enter enclosed or confined space
without proper protective equipment
including respiratory protection.

Spill or leak:

Con tain  spill  im me di ately  in  small est  area  pos si ble. 
Re cover as much of the prod uct it self as pos si ble
by such meth ods as vac u um ing, fol lowed by soak -
ing up of re 

sid 

ual flu 

ids by use of ab 

sor 

bent

materials. 

Re move  con tam i nated  items  in clud ing  con tam i -
nated soil and place in proper con tain ers for dis -
posal. Avoid wash 

ing, drain 

ing, or di 

rect 

ing

ma te rial to storm or san i tary sewers .

Waste disposal method:

Re cy cle as much of the re cov er able prod uct as
pos si ble. 

Dis pose  of  non-re cy cla ble  ma te rial  as  a  RCRA
haz ard ous  waste  by  such  meth ods  as  in cin er a tion,
c o m  p l y  in g   w i t h   f e d  e r a l ,   s t a t e ,   a n d   l o  c a l
regulations.

Foam In Tires

Extinguishing media:

Wa ter, dry chem i cal, foam, or CO2.

Special fire fighting procedures:

Evac u ate non emer gency per son nel to a safe area.

Unusual fire and explosion hazards:

Fire fight ers should use self con tained breath ing
ap pa ra tus. Avoid breath ing smoke, fumes, and de -
com po si tion  prod ucts. 

Use wa ter spray to drench smol der ing elas to mer.
Prod uct may melt, af ter ig ni tion, to form flam ma ble
liquid.

Burning produces intense heat, dense
smoke, and toxic gases, such as carbon
monoxide, oxides of nitrogen, and traces of
hydrogen cyanide.

Spill or leak:

Pick up and han dle as any other in ert solid ma te -
rial.

Waste disposal method:

Not  con sid ered  a  haz ard ous  ma te rial.  Dis pose  of
ma te rial ac cord ing to any lo cal, state, and fed eral
reg u la tions.

Gasoline (UN 1203)

Extinguishing media:

Dry chem i cal, foam, or CO2.

Special fire fighting procedures:

Wa ter may be in ef fec tive to ex tin guish, but wa ter
should be used to keep fire ex posed con tain ers
cool. If a leak or spill has not ig nited, use wa ter
spray to dis perse the va pors and to pro tect per son -
nel at tempt ing to stop a leak. Wa ter spray may be
used to flush spills away from ar eas of potential
ignition.

Unusual fire and explosion hazards:

Highly  Flam ma ble.  Prod ucts  of  com bus tion  may
con tain  car bon  mon ox ide,  car bon  di ox ide  and
other  toxic  ma te ri als. 

DO NOT enter enclosed or confined space
without proper protective equipment
including respiratory protection.

Spill or leak:

Re view fire and ex plo sion haz ards be fore pro ceed -
ing with clean up. Use ap pro pri ate per sonal pro tec -
tive equip ment dur ing clean up. Dike spill. Pre vent
liq uid from en ter ing sew ers, wa ter ways, or low ar -
eas. Soak up with saw dust, sand, oil dry or other
ab sor bent ma te rial. Shovel or sweep up.

Re move source of heat, sparks, flame, im pact, fric -
tion  or  elec tric ity  in clud ing  in ter nal  com bus tion  en -
gines and power tools. If equip ment is used for spill
cleanup, it must be ex plo sion proof and suit able for
flam ma ble  liq uid  and  vapor.

page  11 - 2

Rev A

EPV Series – 1596(A)

11. Fire Fighting and Chemical Containment

DANGER

DANGER

DANGER

Summary of Contents for EPV Series


























































Reviews: