background image

5

Using As a Surround Speaker

The compact size and neutral tonal quality of the OH-S7 and OH-T7 make them perfect for the 
surround channel speakers of a home theater system. Place the speakers toward the back of the 
room, to the sides of, or behind the listening 
position.

An indirect sound path from the speakers to 
the listening position results in a more diffuse 
and convincing surround sound effect. This 
can be achieved by taking advantage of the 
angled waveguide tweeter. Orient (rotate) 
the speakers so that the tweeters point away 
from the listening area. Mounting speakers 
fairly far back, and fairly high, on the side 
walls, with the tweeter aimed toward the rear 
wall of the listening area, will give excellent 
results.

PAINTING THE SPEAKERS

If you intend to paint the speakers, it’s best to do so before you install them. Typically, a primer 
coat is not necessary.

1.  Remove the speaker grille. Carefully pry on one edge with an awl or small screwdriver. If 

you choose to paint the metal grille, do so after detaching it from the speaker. 

 

Note:

 You may fi nd it helpful to thin the paint to be used on 

the grille. This prevents the paint from fi lling the holes.

2.  Use the form-fi tting painting mask provided to paint 

the housing. Shape it into a cone and insert the two 
tabs into their adjacent slots.

3.   After the paint has dried, remove the mask by care-

fully inserting a screwdriver into the slots and prying 
upward.

PREPARING FOR INSTALLATION 

Take the following steps to prepare for installation:

/

  Map out the wiring paths from the speakers to the amplifi er. We recommend 16-gauge 

cable or thicker for runs up to 25 feet (8m) and 12-gauge wire or thicker for longer runs. 

/

  Be sure the speaker wire does not rest or rub against any sharp or pointed objects.

/

  Each speaker is 8 ohms nominal. When connecting more than two speakers per amplifi er 

channel, you should use series wiring or an impedance protection device, such as a line 
transformer.

/

  Make sure that the total system’s impedance does not fall below the amplifi er’s minimum 

rating. If you are not certain, consult your Snell Acoustics dealer.

OH-S7 and OH-T7.indd   5

OH-S7 and OH-T7.indd   5

1/22/08   7:17:23 PM

1/22/08   7:17:23 PM

Summary of Contents for OH-S7









Reviews: