background image

2

GENERAL OPERATION

1. Read, understand, and follow all instructions in the

manual and on the unit before starting.

2. Do not put hands or feet near rotating parts or under

the machine. Keep clear of the discharge opening at
all times.

3. Only allow responsible adults, who are familiar with

the instructions, to operate the unit (local regulations
can restrict operator age).

4. Clear the area of objects such as rocks, toys, wire,

etc., which could be picked up and thrown by the
blade(s).

5. Be sure the area is clear of other people before mow-

ing. Stop the unit if anyone enters the area.

6. Never carry passengers.
7. Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while travel-
ling in reverse.

8. Never direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction.
Material may ricochet back toward the operator. Stop
the blade(s) when crossing gravel surfaces.

9. Do not operate the machine without the entire grass

catcher, discharge guard (deflector), or other safety
devices in place and operational.

10. Slow down before turning.
11. Never leave a running unit unattended. Always disen-

gage the blades (PTO), set parking brake, stop
engine, and remove keys before dismounting.

12. Disengage blades (PTO) when not mowing. Shut off

engine and wait for all parts to come to a complete
stop before cleaning the machine, removing the grass
catcher, or unclogging the discharge guard.

13. Operate the machine only in daylight or good artificial

light.

14. Do not operate the unit while under the influence of

alcohol or drugs.

15 Watch for traffic when operating near or crossing

roadways.

16. Use extra care when loading or unloading the unit

into a trailer or truck.

17. Always wear eye protection when operating this unit.
18. Data indicates that operators, age 60 years and

above, are involved in a large percentage of power
equipment-related injuries. These operators should
evaluate their ability to operate the equipment safely
enough to protect themselves and others from injury.

19. Follow the manufacturer’s recommendations for wheel

weights or counterweights.

20. Keep in mind the operator is responsible for accidents

occurring to other people or property.

21. All drivers should seek and obtain professional and

practical instruction.

22. Always wear substantial footwear and trousers.

Never operate when barefoot or wearing sandals.

23. Before using, always visually check that the blades

and blade hardware are present, intact, and secure.
Replace worn or damaged parts.

24. Disengage attachments before: refueling, removing

an attachment, making adjustments (unless the
adjustment can be made from the operator’s posi-
tion).

25. When the machine is parked, stored, or left unattend-

ed, lower the cutting means unless a positive
mechanical lock is used.

26. Before leaving the operator’s position for any reason,

engage the parking brake (if equipped), disengage
the blades (PTO), stop the engine, and remove the
key.

27. To reduce fire hazard, keep the unit free of grass,

leaves, & excess oil. Do not stop or park over dry
leaves, grass, or combustible materials.

28. It is a violation of California Public Resource Code

Section 4442 to use or operate the engine on or near
any forest-covered, brush-covered, or grass-covered
land unless the exhaust system is equipped with a
spark arrester meeting any applicable local or state
laws. Other states or federal areas may have similar
laws.

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control 
of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.

This mowing deck is capable of amputating hands and feet and throwing objects.

The triangle         in text signifies important cautions or warnings which must be followed.

Safety Rules & Information

TRANSPORTING AND STORAGE

1. When transporting the unit on an open trailer, make

sure it is facing forward, in the direction of travel. If
the unit is facing backwards, wind lift could damage
the unit.

2. Always observe safe refueling and fuel handling prac-

tices when refueling the unit after transportation or
storage.

3. Never store the unit (with fuel) in an enclosed poorly

ventilated structure. Fuel vapors can travel to an igni-
tion source (such as a furnace, water heater, etc.)
and cause an explosion. Fuel vapor is also toxic to
humans and animals.

4. Always follow the engine manual instructions for

storage preparations before storing the unit for both
short and long term periods.

5. Always follow the engine manual instructions for

proper start-up procedures when returning the unit to
service.

6. Never store the unit or fuel container inside where

there is an open flame or pilot light, such as in a
water heater. Allow unit to cool before storing.

TP 600-4103-00-ZT-UV

Summary of Contents for ZT 1844





































Reviews: