background image

30

2 YEAR LIMITED WARRANTY

For two (2) years from purchase date for the original purchaser's use, 

SNAPPER

, through any authorized

SNAPPER

 

dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon

examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.

SNAPPER

 FIELD SERVICEABLE SPINDLES and their components used on 

SNAPPER PRO

®

 Mid Size walks

and 

SNAPPERZRIDER

®

 ride on commercial equipment have a three (3) year limited warranty against defects in

material or workmanship or both.

All transportation costs incurred by the purchaser in submitting material to an authorized 

SNAPPER

 

dealer for

replacement under this warranty must be paid by the purchaser.

This warranty does not apply to engines and their components, and batteries, as these items are warranted

separately. This warranty does not apply to parts that have been damaged by accident, alteration, abuse,

improper lubrication, normal wear, or other cause beyond the control of 

SNAPPER

. This warranty does not

cover any machine or component that has been altered or modified, changing safety, performance, or durability.

Batteries have a one (1) year prorated warranty period with free replacement if required during the first ninety

(90) days from the original purchase date. 

SNAPPER

 will not be responsible for any installation cost incurred.

The battery warranty only covers original equipment batteries and does not cover damage to the battery or

machine caused by neglect or abuse, destruction by fire, explosion, freezing, overcharging, improper

maintenance, or use of improper electrolyte.

There is no other express warranty.

DISCLAIMER OF WARRANTY

Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to

two (2) years from purchase date for the original purchaser's use, and up to the extent permitted by law

and all implied warranties are excluded. This is the exclusive remedy. Liabilities for consequential

damages, under any and all warranties are excluded.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may

not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

WARNING: THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR
THE SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER
ASSOCIATED WITH THE USE OF SUCH PARTS.

IMPORTANT:

 Please fill out the attached 

SNAPPER

 Product Registration Card immediately and mail to:

Snapper’s Product Registration Center,

 P.O. Box 1379, McDonough, Georgia. 30253

Summary of Contents for ZF2101DKU





































Reviews: