background image

 

IMPORTANT SAFETY INSTRUCTIONS 

 

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that 
can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious 
injury or death to the operator or other persons. The owner of the machine must understand these instructions 
and must allow only persons who understand these instructions to operate machine. Each person operating the 
machine must be of sound mind and body and must not be under the influence of any substance, which might 
impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your dealer 
cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, 
Georgia 30253. Phone: (1-800-935-2967). 

 

PROTECTION FOR CHILDREN  

Tragic accidents can occur if the operator is not alert 
to the presence of children. Children are often 
attracted to the machine and the mowing activity. 
Never assume that children will remain where you last 
saw them. 
1.  KEEP children out of the mowing area and under 

the watchful care of a responsible adult.  

2.  DO NOT allow children in yard when machine is 

operated (even with the blades OFF).  

3.  DO NOT allow children or others to ride on 

machine or on attachments (even with the blade 
OFF). They may fall and be seriously injured.  

4.  DO NOT allow pre-teenage children to operate 

machine. 

5.  ALLOW only adults or responsible teenagers with 

mature judgment under close adult supervision to 
operate machine. 

6.  DO NOT operate blades in reverse. STOP BLADES. 

LOOK and SEE behind and down for children, pets 
and hazards before and while backing. 

7. USE EXTRA CARE when approaching blind 

corners, shrubs, trees, or other objects that may 
obscure vision.  

 

PROTECTION AGAINST TIPOVERS  

Slopes are a major factor related to loss-of-control 
and tip-over accidents, which can result in severe 
injury or death. All slopes require extra CAUTION. If 
you cannot back up the slope or if you feel uneasy on 
the slope, DO NOT mow it. Use extra care with grass 
catchers or other attachments; these affect the 
handling and the stability of the machine.  
1.  DO NOT operate machine on slopes exceeding 15 

degrees (27% grade). 

2.  Exercise EXTREME CAUTION on slopes above 10 

degrees (18% grade). Turn blades OFF when 
traveling uphill. Use a slow speed and avoid 
sudden or sharp turns.  

3.  DO NOT operate machine back and forth across 

face of slopes. Operate up and down. Practice on 
slopes with blades off. 

 
 
 
 
 

PROTECTION AGAINST TIPOVERS  

(Continued From Previous Column) 
4.  AVOID uphill starts. If machine stops going uphill 

or tires lose traction, turn blades OFF and back 
slowly down the slope.  

5.  STAY ALERT for holes and other hidden hazards. 

Tall grass can hide obstacles. Keep away from 
ditches, washouts, culverts, fences and 
protruding objects.  

6.  KEEP A SAFE DISTANCE (at least 3 feet) away 

from edge of ditches and other drop offs. The 
machine could turn over if an edge caves in.  

7.  Always begin forward motion slowly and with 

caution.  

8.  Use weights or a weighted load carrier in accordance 

with instructions supplied with a grass catcher. DO 
NOT operate machine on slopes exceeding 10 
degrees (18% grade) when equipped with grass 
catcher. 

9.  DO NOT put your foot on the ground to try to 

stabilize the machine.  

10. DO NOT operate machine on wet grass. Reduced 

traction could cause sliding.  

11. DO NOT operate machine under any condition 

where traction, steering or stability is doubtful. 

12. Operator Protective Structures are available for 

this machine through your local Snapper dealer. 

 

PREPARATION 

1.  Read, understand and follow instructions and 

warnings in this manual and on the machine, 
engine and attachments. Know the controls and 
the proper use of the machine before starting. 

2.  Only mature, responsible persons shall operate 

the machine and only after proper instruction.  

3.  Data indicates that operators age 60 and above, 

are involved in a large percentage of mower-
related injuries. These operators should evaluate 
their ability to operate the mower safely enough to 
protect themselves and others from serious injury. 

4.  Handle fuel with extra care. Fuels are flammable 

and vapors are explosive. Use only an approved 
fuel container. DO NOT remove fuel cap or add 
fuel with engine running. Add fuel outdoors only 
with engine stopped and cool. Clean spilled fuel 
from machine. DO NOT smoke. 

 
 

Summary of Contents for ZF2100DKU

































Reviews: