22
TROUBLESHOOTING
PROBLEM
PROBABLE CAUSE
CORRECTIVE ACTION
Rider Will Not Move Or 1. Joystick in the neutral “N” position.
1. Place joystick in desired speed position.
Loss Of Traction
2. Roll release lever is in “ROLL” position.
2. Move roll release lever to the engaged position.
3. Low transmission hydraulic oil level.
3. Contact authorized SNAPPER dealer.
4. Parking Brake engaged.
4. Move parking brake to disengaged position..
5. Traction drive belt requires replacement
5. Replace traction drive belt.
Blade(s) Not Cutting
1. Blade engagement switch in the “OFF” position.
1. Move blade switch to the “ON” position.
2. Clutch belt slipping.
2. Replace clutch belt.
3. Mower belt slipping.
3. Replace mower belt.
4. Electric clutch not functioning.
4. Contact authorized SNAPPER dealer.
Cutting Grass
1. Uneven tire pressure.
1. Bring to proper pressure.
Improperly
2. Cutting height too low or high.
2. Adjust cutting height.
3. Engine speed too slow.
3. Move throttle control to “FAST” position.
4. Forward speed too fast.
4. Move joystick to a slower speed.
5. Terraced cut, side to side.
5. Adjust side to side level
6. Excessive deck pitch, front to rear.
6. Adjust front to rear pitch.
7. Cutting blade(s) dull or damaged.
7. Sharpen cutting edges or replace blade(s).
8. Blade belt slipping.
8. Replace blade belt.
9. Check electric clutch.
9. Adjust to proper specifications. (33” Deck Only)
10. Check clutch belt.
10. Replace clutch belt.
Poor Grass Discharge 1. Engine speed too slow.
1. Move throttle control to “FAST” position.
2. Forward speed too fast.
2. Move joystick to a slower speed.
3. Grass is wet.
3. Mow when grass is dry.
4. Excessively worn or damaged blade(s).
4. Service mower blade(s)
5. Build up of grass clippings and debris under deck. 5. Clean deck.
6. Improper blade(s) installed on deck.
6. Install proper SNAPPER blades.
7. Blade(s) installed improperly on deck.
7. Install blades properly.
Battery Will Not Charge 1. Poor cable connections.
1. Clean cables and battery terminals.
2. Bad battery cell(s)
2. Replace with new battery.
3. Faulty alternator.
3. Contact engine manufacturer’s dealer.
Oil Leaking
1. Leaking hose fittings, clamps or reservoir.
1. Verify fittings and hose clamps are tight.
4.7. MAINTENANCE/REPLACEMENT
PARTS
MAINTENANCE/REPLACEMENT PARTS
Engine Speed Control Cable (Briggs 14 HP)
2-4642
Engine Speed Control Cable (Kohler 15 HP)
3-6506
Engine Speed Control Cable (Kohler 18 HP)
4-2992
Choke Control Cable (Kohler 15 HP)
2-4185
Choke Control Cable (Kohler 18 HP)
2-4185
33” Cutter Deck Blade
3-4168
38” Cutter Deck Blade (2 Blades Required)
4-2998
42” Cutter Deck Blade (2 Blades Required)
2-6691
48” Cutter Deck Blade (3 Blades Required)
2-9247
33” Cutter Deck Belt (Electric Clutch to Cutting Deck)
3-5389
38” Cutter Deck Belt (Electric Clutch to Cutting Deck)
2-9308
42” Cutter Deck Belt (Electric Clutch to Cutting Deck)
3-6585
48” Cutter Deck Belt (Electric Clutch to Cutting Deck)
4-2997
Wheel Drive Belt (Engine to Hydro Transaxle)
4-1823
Wheel Drive Belt (Engine to Hydro Transaxle) (48” Deck Only)
4-1829
Mower Drive Belt (Engine to Electric Clutch)
2-9117
Mower Drive Belt (Engine to Electric Clutch) (48” Deck Only)
4-6997
Parts Manual for Yard Cruiser Series 1 & 2
06109
Summary of Contents for YARD CRUISER HZS14331BVE
Page 25: ...25 PRIMARY MAINTENANCE...
Page 26: ...26 PRIMARY MAINTENANCE...
Page 27: ...27 PRIMARY MAINTENANCE...
Page 28: ...28 PRIMARY MAINTENANCE...
