background image

Page 12

OPERATOR INSTRUCTIONS ANd PARTS 

  1695924 Chipper/Shredder

Figure 21.  Installing the hopper handle

A.  1/4-20 x 3/4 Screw & Nut

Initial Assembly

A

Install the hopper - All Models

 1.  Remove two 1/4 locknuts and flat washers from 

hopper liner and set aside. Attach the hopper to the 

rotor housing.  Make sure to engage the metal lip of 

the hopper liner inside the housing.

 2.  Secure the hopper to the rotor housing using two 

5/16 x 1/2 hex head bolts, two 5/16 flat washers and 

hardware removed from step 1 (Figure 19).  Do not 

tighten hardware at this time.

 3.  See Figure 20.  From the inside of the hopper install 

one 5/16-18 x 3/4 hex head bolt, 5/16 lockwasher, 

and 5/16 flat washer into each of the upper and lower 

holes of the metal hopper liner.  Finger tighten only at 

this time.

 4.  Check that the hopper is seated correctly and tighten 

all hardware.

Install the handle - All Models

 1.  Lift the hopper handle up until the outer holes in the 

handle align with the holes in the shredder hopper 

and secure with 1/4-20 x 3/4 screws, washers, and 

nuts (A, Figure 21).  Insert the screws from the 

outside of the shredder hopper.

Figure 20.  Installing hardware Inside the hopper

Figure 19.  Attaching the hopper

Not 

for  

Reproduction

Summary of Contents for Snapper 165924





























Reviews: