background image

2

Safety Rules & Information

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause
injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to
the operator or other persons. The owner of the machine must understand these instructions and must allow only per-
sons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
and body and must not be under the influence of any substance, which might impair vision, dexterity or judgment. If you
have any questions pertaining to your machine which your dealer cannot answer to your satisfaction, call or write the
Customer Service Department at SNAPPER Products Inc., McDonough, Georgia 30253. Phone: (1-800-935-2967).

PROTECTION FOR CHILDREN 

Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Children who have
been given rides in the past may suddenly appear in the
mowing area for another ride and be run over or backed
over by the machine. Never assume that children will
remain where you last saw them.

1.

KEEP children out of the mowing area and under the watch-
ful care of a responsible adult other than the operator. 

2.   DO NOT allow children in yard when machine is operated

(even with the blade OFF). 

3.   DO NOT allow children or others to ride on machine, attach-

ments or towed equipment (even with the blades OFF). They
may fall and be seriously injured. 

4. 

DO NOT allow pre-teenage children to operate machine.

5.  ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate machine. 

6.  DO NOT operate blades in reverse. STOP BLADES. LOOK

and SEE behind and down for children, pets and hazards
before and while backing.

7. 

USE EXTRA CARE when approaching blind corners, shrubs,
trees, or other objects that may obscure vision. 

PROTECTION AGAINST TIPOVERS 

Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or
death. All slopes require extra CAUTION. If you cannot
back up the slope or if you feel uneasy on the slope, DO
NOT mow it. Use extra care with grass catchers or other
attachments; these affect the handling and the stability of
the machine. 

1.  DO NOT operate machine on slopes exceeding 15 degrees

(27% grade).

2.  Exercise EXTREME CAUTION on slopes above 10 degrees

(18% grade). Turn blades OFF when traveling uphill. Use a
slow speed and avoid sudden or sharp turns. 

3.  DO NOT operate machine back and forth across face of

slopes. Operate up and down. Practice on slopes with blades
off.

4.  AVOID starting, stopping or turning on slopes. If machine

stops going uphill or tires lose traction, turn blades OFF and
back slowly straight down the slope. 

PROTECTION AGAINST TIPOVERS 

(Continued From Previous Column)

5.   STAY ALERT for holes and other hidden hazards. Tall grass

can hide obstacles. Keep away from ditches, washouts, cul-
verts, fences and protruding objects. 

6.   KEEP A SAFE DISTANCE (at least 3 feet) away from edge of

ditches and other drop offs. The machine could turn over if
an edge caves in. 

7.   Always begin forward motion slowly and with caution.
8.   Use weights or a weighted load carrier in accordance with

instructions supplied with a grass catcher. DO NOT operate
machine on slopes exceeding 10 degrees (18% grade) when
equipped with grass catcher.

9.   DO NOT put your foot on the ground to try to stabilize the

machine. 

10.  DO NOT operate machine on wet grass. Reduced traction

could cause sliding. 

11.  Chose a low enough speed setting so that you will not have

to stop or shift on a slope. Tires may lose traction on slopes
even though the brakes are functioning properly.

12. DO NOT operate machine under any condition where trac-

tion, steering or stability is doubtful.

13.  Always keep the machine in gear when going down slopes.

DO NOT shift to neutral (or actuate hydro roll release) and
coast downhill.

PREPARATION

1.   Read, understand, and follow instructions and warnings in

this manual and on the machine, engine and attachments.
Know the controls and the proper use of the machine before
starting.

2.   Only mature, responsible persons shall operate the machine

and only after proper instruction. 

3.   Data indicates that operators age 60 and above, are involved

in a large percentage of mower-related injuries. These opera-
tors should evaluate their ability to operate the mower safely
enough to protect themselves and others from serious injury.

4.   Handle fuel with extra care. Fuels are flammable and vapors

are explosive. Use only an approved fuel container. DO NOT
remove fuel cap or add fuel with engine running. Add fuel
outdoors only with engine stopped and cool. Clean spilled
fuel from machine. DO NOT smoke. 

5.

Practice operation of machine with BLADES OFF to learn
controls and develop skills.

!

!

Summary of Contents for Simplicity 2690474





































Reviews: