background image

 

11

Section 3 - MAINTENANCE 

 
3.1 INTRODUCTION 

To retain the quality of the SCRAMBLER, use genuine 
SNAPPER replacement parts only.  Contact a local 
SNAPPER dealer for parts and service assistance. For 
the correct part or information for a particular mower, 
always mention the model and serial number.  
 

3.2  SERVICE - AFTER FIRST 5 HOURS 
 

WARNING 

DO NOT attempt any adjustments, maintenance, 
service or repairs with the engine running. STOP 
engine. STOP blade. Engage parking brake. Remove 
key. Remove spark plug wire from spark plug and 
secure away from plug. Engine and components are 
HOT. Avoid serious burns, allow all parts to cool 
before working on machine. Fuel Filler Cap and vent 
must be closed securely to prevent fuel spillage. 

 

3.2.1.  CHANGE ENGINE OIL 
1. 

Place bricks or wooden blocks under the front 

wheels to lower rear of engine. 

2. 

Place a 4 quart minimum capacity container 

under the end of the oil drain. 

3.

  Loosen or remove oil fill cap on engine. 

4.

  Install the drain hose (Supplied in hardware bag) 

onto drain plug nipple and place hose into drain 
container. 

5. 

Rotate drain plug counter clockwise and pull out 

to open and allow oil to drain out. See Figure 3.1. 

 

 

FIGURE 3.1 

 

6.

 After all the oil has drained, close the drain by 

pushing in and rotating clockwise to close. Wipe up 
any oil that may have spilled. Dispose of drained oil 
properly. See Figure 3.1. 

7.

  Change oil filter at every oil change.  Refer to your 

engine owner’s manual for service instructions. 

8.

  Fill engine crankcase with new oil.  Refer to your 

engine owner’s manual for oil specifications. 
 

3.2.2.  CHECK MOWER BLADE 
1.

 Close vent on fuel cap and make sure cap is 

tight. Close fuel valve in fuel line. Start engine and 
allow it to run until engine runs out of fuel. 

2.

  Apply parking brake. 

3.

  Turn key to “OFF” position and remove key from 

ignition switch. 

 

WARNING 

Wear heavy leather gloves when handling or working 
around cutting blades. Blades are extremely sharp and 
can cause severe injury.  

 

4.

  Carefully stand SCRAMBLER on rear bumper. It 

may be necessary to have help to stand unit up. 

5.

  Check torque of blade mounting bolts. Torque to: 

33” Deck - 30 to 40 ft. lbs.  
38” Deck - 80 to 90 ft. lbs. See Figure 3.2. 

6.

 Check blade for sharpness, wear and damage. 

Refer to Section “BLADE WEAR LIMITS”. 

 

FIGURE 3.2 

 

7.

  Check blade for straightness. 

 

WARNING

 

DO NOT use a cutting blade that shows signs of 
excessive wear or damage. Refer to Section 
“MOWER BLADE REPLACEMENT” for proper blade 
inspection and service procedures.  

 

INSTALL HOSE 
ONTO OIL DRAIN 
NIPPLE 

ROTATE 1/4 TURN 
COUNTERCLOCKWISE 
AND PULL OUT TO DRAIN 
ENGINE OIL 

OIL DRAIN 

TORQUE BLADE MOUNTING 
BOLTS TO 30 TO 40 FT. LBS. 

SINGLE BLADE DECK 

TORQUE BLADE MOUNTING 
BOLTS TO 80 TO 90 FT. LBS. 

TWIN BLADE DECK 

Summary of Contents for SCRAMBLER YZ16335BVE






































Reviews: