background image

 

25

TROUBLESHOOTING 

 

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

Starter Will Not Crank

  1. Battery dead. 

1. Service battery. 

Engine

 

2. Blown fuse. 

2. Replace fuse. 

 

3. Electrical connections loose or corroded. 

3. Clean and check connections for good contact. 

 

4. Defective ignition switch. 

4. Contact authorized 

SNAPPER

 dealer. 

 

5. Blade engagement switch in the “ON” position. 

5. Push blade engagement switch in to “OFF”. 

 

6. Motion Control Levers not in neutral lock position. 

6. Lift levers into neutral lock position. 

 

7. Park brake not engaged. 

7. Engage park brake. 

 

8. Faulty parking brake, blade or ignition switch. 

8. Contact authorized 

SNAPPER

 dealer. 

 

9. Faulty engine starter. 

9. Replace engine starter. 

 

10. Faulty starter solenoid. 

10. Replace starter solenoid. 

Engine Will Crank But 

  1. Fuel tank empty or fuel shut-off valve closed. 

1. Fill fuel tank with fresh fuel & open fuel valve. 

Not Start

 

2. Engine needs choking. 

2. Move choke control to “CHOKE” position. 

 

3. Spark plug wire disconnected. 

3. Place spark plug wire onto spark plug. 

 

4. Battery weak or dead. 

4. Service battery. 

 

5. Faulty parking brake, blade or ignition switch. 

5. Contact authorized 

SNAPPER

 dealer. 

Engine Will Not Start 

  1. Blade engagement switch in the “ON” position. 

1. Push blade engagement switch in to “OFF”. 

Using Recoil Starter

 

2. Park brake not engaged. 

2. Engage park brake. 

(Applicable models) 

3. Motion Control Levers not in neutral lock position. 

3. Lift levers into neutral lock position. 

 

4. Fuel tank empty or fuel shut-off valve closed. 

4. Fill fuel tank with fresh fuel & open fuel valve. 

 

5. Engine needs choking. 

5. Move choke control to “CHOKE” position. 

 

6. Blown Fuse. 

6. Replace with new 20 AMP fuse. 

 

7. Faulty relay switch. 

7. Contact authorized 

SNAPPER

 dealer. 

 

8. Faulty parking brake or blade switch. 

8. Contact authorized 

SNAPPER

 dealer. 

Engine Stalls After 

 

1. Operator not in seat. 

1. Sit in operator’s seat. 

Running

 

2. Engine speed control in the “CHOKE” position. 

2. Move speed control back past “Fast” detent. 

 

3. Fuel tank empty. 

3. Fill with fuel to proper level. 

 

4. Engine air pre-cleaner and or air cleaner dirty. 

4. Clean free of all debris. 

 

5. Spark plug defective or gap set improperly. 

5. Service spark plug. 

 

6. Fuel filter stopped up. 

6. Replace fuel filter. 

 

7. Water, debris or stale fuel in fuel system. 

7. Drain and clean fuel system. 

Engine Loses Power

  1. Excessive load on engine. 

1. Lessen load. 

 

2. Engine air pre-cleaner or air cleaner dirty 

2. Clean or replace filters. 

 

3. Spark plug faulty. 

3. Service spark plug. 

 

4. Water, debris or stale fuel in fuel system. 

4. Drain and clean fuel system. 

 

5. Debris build up on engine cooling screen. 

5. Clean all debris from engine cooling screen. 

Engine Backfires When 
Turned To “STOP”

 

1. Throttle control set too “FAST”. 

1. Set throttle control to “SLOW” and allow engine 

to idle.  Then, turn key to “OFF”. 

 

(Trouble Shooting Continued on Next Page) 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

27

Summary of Contents for SCRAMBLER SZT18336BVE





































Reviews: