Snap-On EEWH311B Operation Instructions Manual Download Page 11 | Manualshive

Page: 11 / 28

background image

Page 11

Operation Manual

1.4

FLOOR AND SPACE REQUIREMENTS

1104

Figure 1.3-1

1.5 GENERAL CAUTIONS

A. DURING THE USE AND MAINTENANCE OF THE
MACHINE IT IS MANDATORY TO COMPLY WITH
ALL LAWS AND REGULATIONS FOR ACCIDENT
PREVENTION.

B. THE ELECTRICAL POWER SOURCE MUST HAVE A
GROUND CABLE AND THE GROUND CABLE OF THE
MACHINE MUST BE CONNECTED TO THE GROUND
CABLE OF THE POWER SOURCE.

C. BEFORE ANY MAINTENANCE OR REPAIRS
ARE ACCOMPLISHED THE MACHINE MUST BE
DISCONNECTED FROM THE AIR AND ELECTRICAL
SUPPLY.

D. NEVER WEAR TIES, CHAINS OR OTHER LOOSE
ARTICLES WHEN USING, MAINTAINING OR
REPAIRING THE MACHINE. LONG HAIR IS ALSO
DANGEROUS AND SHOULD BE KEPT UNDER A HAT.
THE USER MUST WEAR PROPER SAFETY ATTIRE -
GLOVES, SAFETY SHOES AND GLASSES.

2.0 INSTALLATION

Your new EEWH311B Air-Electric Tire Changer requires

a simple installation procedure requiring only a few

moments.

Follow these instructions carefully to insure proper and

safe operation.

The Tire Changer is delivered mounted to a wooden skid.

Remove tire changer from its mounts carefully , taking

care to avoid any back strain.

Place Tire Changer where proper operation will be

unobstructed to all sides. Install the machine in a covered

and dry place.

2.0.1 ANCHORING

Once placed in the desired location the tire changer must

be bolted to the f oor.

Secure the machine to the floor through the holes

provided in the cabinet, using 3/8” x 2” anchor bolts

(Recommended).

2.1 ELECTRICAL INSTALLATION

BUILDING ELECTRICAL INSTALLATION MUST BE
MADE BY A LICENSED ELECTRICIAN.

Check that the electrical speci f cations of the power

source are the same as the machine. The machine uses

115V, 60 hz, grounded single phase 20 amp source.

Electric specif cations are clearly marked on a label at

the side of the machine.

FAILURE TO PROVIDE PROPER ELECTRICAL
SUPPLY AND GROUNDING WILL CREATE A SHOCK
HAZARD TO THE OPERATOR.

540

EEWH311B Air-Electric Tire Changer

«
...
9
10
11
12
13
...
»

Summary of Contents for EEWH311B





























Reviews:

No comments

Related manuals for EEWH311B

Brand: Ranger Products Pages: 56

Brand: Protec Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands