SMSC EMC1046 User Manual Download Page 9

Page: 9 / 10

EMC1046/47 EVB User Manual

SMSC EMC1046/47

Revision 1.0 (08-21-07)

3.9

Default Jumper Settings

Table 3.3 Default Jumper Settings

Note:

dashed line indicates jumper position

3.10

Other Sensor Features

Other features such as Ideality Factor Configuration, Conversion Rate, and Digital Filtering can be
controlled with EMC1046/47 registers. See the datasheet register description for details.

JUMPER

NAME

CONNECTION

DESCRIPTION

JP1

Remote 1 off-

board diode

connection

1 - 2

3 - 4

DP connection

DN connection

JP2

Remote 2 off-

board diode

connection

1 - 2

3 - 4

DP connection

DN connection

JP3

Remote 3 off-

board diode

connection

1 - 2

3 - 4

DP connection

DN connection

JP4

Remote 4 off-

board diode

connection

1 - 2

3 - 4

DP connection

DN connection

JP5

Remote 5 off-

board diode

connection

1 - 2

3 - 4

DP connection

DN connection

JP6

Remote 6 off-

board diode

connection

1 - 2

3 - 4

DP connection

DN connection

JP19

USB to SMBus

1 - 2

3 - 4

5 - 6

7 8 (open)

+3.3V

SDA - SMBus

SCL - SMBus

No connection

Bias

connections for

remote CPU

transistor

1 2 (open)

Vbias ~ 0.7V

GND

Flash Prog

Header

Used in manufacturing

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Summary of Contents for EMC1046











Search results

Summary of Contents for EMC1046

Reviews:

Brands by name

Popular brands

SMSC EMC1046, User Manual

Search results

Summary of Contents for EMC1046

Reviews:

Brands by name

Popular brands