background image

SMOKEMASTER

®

 

MODELS F72A & F72B 

 

INDUSTRIAL ELECTRONIC AIR CLEANER 

 

 
 
 

THE F72 INDUSTRIAL ELECTRONIC AIR CLEANERS INCLUDE COMPONENTS REQUIRED 
TO REMOVE AIRBORNE PARTICLES SUCH AS COOLANT MIST, DUST, SOOT, POLLEN, 
BACTERIA, TOBACCO AND COOKING SMOKE FROM THE CIRCULATING AIR IN LARGE 
RESIDENTIAL, COMMERICAL AND INDUSTRIAL MANUFACTURING FACILITIES.  THE AIR 
CLEANER IS MOUNTED IN THE RETURN AIR DUCT OF A FORCED AIR SYSTEM WHERE 
AMBIENT TEMPERATURE DOES NOT EXCEED 125°F (52°C).  ONE OR TWO ELECTRONIC 
CELLS, OPERATED BY HIGH VOLTAGE POWER SUPPLIES, REMOVE AIRBORNE 
CONTAMINANTS AT EFFICIENCIES AS HIGH AS 99 PERCENT.  PERFORMANCE IS 
MONITORED BY A STATUS LIGHT ON THE POWER SUPPLY. 

 

x

 

Cleans the air at a rate of 1,000 to 12,000 cfm 
(1,699 to 20,390 m³/hr.) in forced air systems. 

x

 

Rated 80 to 99 percent efficient according to 
the National Bureau of Standards Dust Spot 
Method using atmospheric dust. 

x

 

Same high capacity, industrial electronic cell 
used in all models. 

x

 

Reversible electronic cell allows system 
airflow to enter cabinet from either side. 

x

 

High voltage, solid state power supply retains 
peak efficiency over a wide range of cell dirt 
loading conditions. 

x

 

High voltage power supply uses voltage 
doubler to provide increased ionization 
voltage. 

x

 

F72 models are available in all single phase 
voltages:  100-120 volt, 200-240 volt, 50 or  
60 Hz. 

x

 

Performance indicator light and test button 
provides operational status. 

x

 

Strong, galvanized steel cabinet can be 
installed vertically or horizontally. 

x

 

Hinged power door allows easy access to cells 
and filters. 

Summary of Contents for F72 Series





















Reviews: