PRoGRAmmInG / SET-UP SEQUEnCE
ConTInUoUS DELIVERY
Batteries must be installed; pump must be stopped and in LL1.
noTE: Value not Saved is displayed if a value is scrolled and EnTER/
CLEAR is not pressed. Press nEXT to continue programming.
WARnInG: If the pump is dropped or hit, inspect it for damage. Do not
use a pump that is damaged or is not functioning properly.
View Dose Cycle
PUmP oPERATIonS
1. Stop the pump.
2. Press LOCK.
3. View lock level.
4. Press LOCK or ENTER/CLEAR two more times.
1. Press and hold STOP/START until
(– – – – – – – – – – – –) appears on the display.
2. Release STOP/START key. STOPPED will appear
on the display when the pump is stopped.
1. Press and hold STOP/START until
(– – – – – – – – – – – –) disappears from the display.
2. Release STOP/START key. RUN will appear on the
display when the pump is running.
Pump must be stopped and in LL0 or LL1.
Warning: Do not prime the fluid path with the
tubing connected to a patient as this could result in
over-delivery of medication or air embolism.
1. Press and hold PRIME until the word PRIME
appears on the display, along with (– – – – – – – – – – – –).
2. Release the PRIME key.
3. Press and hold PRIME. Priming appears on the
display. Continue priming until the fluid path is
free of air.
4. Press NEXT to return to the main screen.
1. Stop the pump.
2. Press NEXT to display the reservoir volume screen.
3. Press ENTER/CLEAR to reset the value to previously
programmed amount.
1. Press and hold ON/OFF until pump beeps
and powers up.
1. Press and hold ON/OFF until (•••• •••• ••••)
appears on the display.
2. Release ON/OFF key.
3. The screen will go blank as the pump goes into
a lower power state.
1. Stop the pump.
2. Push down and hold the arrow button on the
battery door while sliding the door off.
Remove and discard old batteries.
ImPoRTAnT: Always stop pump before
removing batteries.
3. Install new batteries, matching polarities shown
on pump. Replace battery door and close.
4. Start the pump.
Warning: If a gap is present anywhere between the
battery door and the pump housing, the door is not
properly latched. If the battery door becomes
detached or loose, the batteries will not be properly
secured which could result in loss of power or
non-delivery of medication.
Warning: Do not use rechargeable niCad or nickel
metal hydride (nimH) batteries. Do not use carbon
zinc (“heavy duty”) batteries.
View Reservoir
Volume
Enter Continuous
Rate
Clear milliliters
Given
Verify Air
Detector Status
Verify Upstream
Sensor Status
Verify
Programming
main Screen
View Reservoir
Volume
View Dose Volume
View Dose Duration
main Screen
View KVo Rate
Verify Dose
Remaining
View the
Lock
Level
Stop the
Pump
Start the
Pump
Press NEXT.
1. Press ENTER/CLEAR to reset.
2. Press NEXT.
3. Press
´
or
Î
to select desired Continuous
Rate in ml/hr.
4. Press ENTER/CLEAR.
5. Press NEXT.
Warning: This pump delivers medication at a
continuous rate or intermittent rate in milliliters
per hour (ml/hr). Programming the pump at a
delivery rate other than what is prescribed will
cause over- or under-delivery of medication.
6. Press ENTER/CLEAR to clear the given
value. The display will show 0.00.
7. Press NEXT.
8. Verify the setting is correct.
9. Press NEXT.
10.Verify the setting is correct.
11.Press NEXT.
12.Press NEXT repeatedly to review program.
InTERmITTEnT DELIVERY
Batteries must be installed; pump must be stopped and in LL1.
Press NEXT.
1. Press ENTER/CLEAR to reset.
2. Press NEXT.
3. Press NEXT.
4. Press NEXT.
5. Press NEXT.
6. Press NEXT.
note: Appears only during dosing or if dose is
interrupted.
7. Press NEXT.
8. Press
´
or
Î
to select amount of time
before next dose. Select IMMEDIATE if
dose should begin when pump is started.
9. Press ENTER/CLEAR.
10. Press NEXT.
11. Press ENTER/CLEAR to clear the given
value. The display will show 0.00.
12. Press NEXT.
13. Verify the setting is correct.
14. Press NEXT.
15. Verify the setting is correct.
16. Press NEXT.
17. Press NEXT repeatedly to review program.
Enter Dose
Starts In
Clear milliliters
Given
Prime the
Fluid Path
Reset the
Reservoir
Volume
Turn the
Pump on
Turn the
Pump off
Change the
Batteries
Verify Air Detector
Status
Verify Upstream
Sensor Status
Verify
Programming
PRoGRAmmInG SCREEnS
main Screen
Displays status of pump
(STOPPED or RUN)
ConTInUoUS moDE
Reservoir Volume
Volume of fluid in reservoir
Continuous Rate
Continuous rate of infusion (ml/hr)
Given
Total amount of medication delivered since
display was last cleared
Air Detector
Indicates if air detector is turned on or off
(status only)
and high or low sensitivity level
Upstream Sensor
Indicates if turned on or off
(status only)
InTERmITTEnT moDE
Reservoir Volume
Volume of fluid in reservoir
Dose Volume
Volume of an individual dose
Dose Duration
Amount of time over which an individual
dose is infused
Dose Cycle
Time from start of one dose to start
of next dose
KVo Rate
Keep Vein Open rate in ml/hr delivered
between
doses
Dose Remaining
Time remaining for delivery of current
dose (only appears during dosing or
if dose is interrupted)
Dose Starts In
Amount of time before start of next dose
Given
Total amount of medication delivered since
display was last cleared
Air Detector
Indicates if air detector is turned on or
(status only)
off and high or low sensitivity level
Upstream Sensor
Indicates if turned on or off
(status only)
IN19893.indd 2
26-10-2011 15:36:21
