Smithco 43-001-A Bunker Rake, Parts & Service Manual, Page: 51 / 110

49
Accessories
42-223 ADJUSTABLE DISC EDGER PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 42-203 Attachment Lift Assembly 1
2 HB-38-16-125 Bolt 3 /
8
- 16 x 1 1 /
4
1
HW-38 Washer 3 /
8
1
HNTL-38-16 Lock Nut 3 /
8
-16 1
3 HB-38-16-150 Bolt 3 /
8
- 16 x 1 1 /
2
2
HW-38 Washer 3 /
8
2
HNTL-38-16 Lock Nut 3 /
8
- 16 2
4 HB-12-13-150 Bolt 1 /
2
- 13 x 1 1 /
2
2
HW-12 Washer 1 /
2
2
HNTL-12-13 Lock Nut 1 /
2
- 13 2
5 42-224 Edger Mount 1
6 13-203 Spindle 1
7 21-169 Bearing and Collar 2
8 13-206 Spindle Shaft 1
9 13-205 1 /
2
Disc Flange 1
10 13-204 Disc 1
11 HMB-34-10 Machine Bushing 3 /
4
x 10GA 4
12 HNA-34-16 Axle Nut 3 /
4
- 16 1
13 HP-18-150 Cotter Pin 1 /
8
x 1 1 /
2
1
14 HWL-38 Washer 3 /
8
1
HW-516 Washer 5 /
16
1
HW-716 Washer 7 /
16
1
15 HB-38-16-100 Bolt 3 /
8
-16 x 1 1
16 HCP-12-200 Clevis Pin 1 /
2
x 2 2
17 HHP-18 Bridge Pin 1 /
8
3
18 HCP-58-250 Clevis Pin 5 /
8
x 2 1 /
2
1
19 HG-14-28-180 Grease Fitting 1 /
4
- 28 x 180 1
INSTALLATION INSTRUCTIONS
1. For initial assembly, bolt spindle assembly (Ref 6) to the edger mount (Ref 5). Use the 1 /
2
- 13 bolts,
washers and lock nuts (Ref 4) to hold in place.
2. Make sure the 1 /
2
" disc flange (Ref 9) is on the spindle shaft (Ref 8) up to the shoulder. Then place the
disc (Ref 10) onto the shaft, curved towards the spindle housing, followed by four machine bushings
(Ref 11), and the axle nut (Ref 12).
3. Tighten axle nut and slide in the cotter pin (Ref 13).
4. The edger mount mounts onto the attachment lift assembly (Ref 1). Use the 3 /
8
bolts, washers and lock
nuts (Ref 2 and 3) with the 1 1 /
4
" bolt going into the last hole on the mount plate.
5. The Edger mounts under the center of the trap rake.
6. Place the handle and linkage onto the empty linkage port of the two bank valve on the machine.
7. Start the engine and lower the cylinder for the attachment lift FULLY. Stop engine.
8. Slide Edger under the trap rake from the right side.
9. Position the lift arms on the attachment lift assembly to the lift brackets on the machine. Hold in place with
1 /
2
x 2 clevis pin and bridge pins (Ref 16 and 17).
10. Attach the cylinder to the center tab on the attachment lift assembly using the 5 /
8
x 2 1 /
2
clevis pin and
bridge pin (Ref 17 and 18).
11. Start engine and test lift and Edger to make sure all works well.