Smeg UD516DSUK Translation Of The Original Instructions Download Page 36

Page: 36 / 37

- Verify that the filter of the tube
placed inside the rinse aid
jerrycan is not clogged.

INSUFFICIENT RINSE

Inappropriate rinse aid, or it
is not dispensed correctly.
Low rinsing temperature

Verify the rinse aid container
and if it is adequate to the type
of mains water.
Verify the boiler set temperature
Restore T Stop ON and/or
connect the machine to hot
water.
If the problem is not solved,
contact the After-Sales Service.

INSUFFICIENT DRYING

Inappropriate rinse aid, or it
is not dispensed correctly.
Water hardness superior
than 12°dF or it contains
many dissolved salts.

Verify the rinse aid container
and if it is adequate to the type
of mains water. If the problem is
not solved, contact the After-
Sales Service

STAINED GLASSES AND
CUTLERY

Rinse aid unsuitable or not
being delivered correctly.

Water hardness above 12°dF
or large amounts of dissolved
salts

Check container of rinse aid and
whether type is suitable for the
mains water- If the problem
persists, contact the after-sales
service.

WATER LEFT IN THE TANK
AFTER PUMP-OUT.

Waste tube badly positioned
or partially clogged.

Verify that the tube and
drainage are not clogged and
that the drainage is not
positioned too high; see
connection scheme.

Summary of Contents for UD516DSUK






































Search results

Summary of Contents for UD516DSUK

Reviews:

Related manuals for UD516DSUK

Brands by name

Popular brands

Smeg UD516DSUK, Translation Of The Original Instructions

Search results

Summary of Contents for UD516DSUK

Reviews:

Related manuals for UD516DSUK

Brands by name

Popular brands