background image

14

Information concerning the water filter

- After use, the water system is subject to low pressure.
  Proceed with caution when removing the filter.

- Flush the water system if the appliance has not been in   
  use for a long period of time, or if the ice/water has an   
  unpleasant taste or smell. To do this, dispense water  
   through the water dispenser for several minutes.
  If the unpleasant taste or smell remains, replace the filter.

- Protect from frost: remove the filter cartridge if you expect  
   the temperature to drop below freezing.

- If pressure surges could occur in the water pipe, do not  
  install the water filter without a suitable surge eliminator.   
  Contact an installation expert if you are not sure whether  
  pressure surges could occur in the water pipe.

- After installing a new filter:
   Discard any ice produced in the first 24 hours after  
  switching on.

- If no ice has been removed for a long period of time, empty 
  the ice box and discard any ice produced over the next   
 24 hours.

How to install Water Line

(For dispenser models)

1. The water pressure should be 2.0~12.5 kgf/cm²
    (1.96 ~12.26 Bar) or more to run the automatic icemaker.
     Check your tap water pressure; if a cup of 180cc is  

 

     full within 10 seconds, the pressure is OK.
2. When installing the water tubes, ensure they are not    
  close to any hot surfaces.
3. The water filter only filters water; it does not eliminate    
  any bacteria or microbes.
4. If the water pressure is not sufficient to run the icemaker,  
  call the local plumber to get an additional water pressure  
 pump.
5. The filter life depends on the amount of use. We  

 

  recommend you to replace the filter at least once every  
 6 

months.

6. After installation of refrigerator and water line system,    
  select [WATER] on your control panel and press it for   
  2~3 minutes to supply water into the water tank and    
 dispense 

water.

7. Use plumbers thread sealing tape on every connection of 
     pipes/tubes to ensure there is no water leaks.
8. The water tube should be connected to the cold water   
 line.

WATER SUPPLY KIT

œ

Check the parts below for installing water supply.

Some other necessary parts are available at your local 
service agents.

Installation Procedure

1. Connecting the appliance

2. Connecting the tap water line

Figure A

Figure B

Place the rubber washer inside the tap connector 
and screw onto the water tap.

Summary of Contents for SR610X



















Reviews: