background image

 

Instructions for use 

 

18

 

1.

 

INSTRUCTIONS FOR USE 

 

 

ELECTRICAL CONNECTION: REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY 
REGULATIONS FOR ELECTRIC OR GAS APPLIANCES AND VENTILATION FUNCTIONS. 
IN YOUR OWN INTEREST, AND THAT OF SAFETY, IT IS THE LAW THAT ALL GAS AND 
ELECTRICAL APPLIANCES BE INSTALLED AND SERVICED BY COMPETENT PERSONS, WHO 
WILL COMPLY WITH THE RELEVANT STANDARDS AND REGULATIONS. 
OUR REGULAR INSTALLERS GUARANTEE A SATISFACTORY JOB. 
GAS OR ELECTRIC APPLIANCES MUST ALWAYS BE DISCONNECTED BY SUITABLY SKILLED 
PEOPLE. 

 

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT 
IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE 
HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE 
USING THE HOB. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN 
ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR 
DOMESTIC USES AND CONFORMS TO THE 

EEC DIRECTIVES

 CURRENTLY IN FORCE. THE 

APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: 

COOKING AND 

HEATING-UP OF FOOD

. ALL OTHER USES ARE CONSIDERED IMPROPER. 

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE

.

 

DO NOT DISCARD PACKING IN THE HOME ENVIRONMENT. SEPARATE THE VARIOUS WASTE 
MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE. 

 

 

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/CE ON 
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT – (WEEE). 
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF RETURN AND 
RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. 
DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL SLITS. 

 

 

THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS 
CLEARLY VISIBLE UNDER THE CASING. A COPY OF THE IDENTIFICATION PLATE IS 
INCLUDED IN THE BOOKLET. 
THE PLATE ON THE CASING MUST NOT BE REMOVED. 
TAKE CARE NOT TO SPILL SUGAR OR SWEET MIXTURES ON TO THE HOB 
WHEN HOT. NEVER PLACE MATERIALS OR SUBSTANCES WHICH MAY MELT 
(PLASTIC OR ALUMINIUM FOIL) ON THE HOB. IN THE EVENT, PROMPTLY 
SWITCH OFF AND REMOVE THE MOLTEN MATERIAL WITH THE SCRAPER 
PROVIDED WHILE THE COOKING ZONE IS STILL WARM TO PREVENT IT 
FROM BEING DAMAGED. 

FAILURE TO INSTANTLY CLEAN THE CERAMIC 

HOB COULD LEAD TO ENCRUSTATIONS WHICH ARE IMPOSSIBLE TO 
REMOVE ONCE THE HOB HAS COOLED DOWN.

 

 

 

The manufacturer declines all responsibility for damage to persons or things caused by non-

observance of the above prescriptions or by interference with any part of the appliance or by 
the use of non-original spares. 

 

Summary of Contents for SE2320ID1















Reviews: