background image

 

 

Instructions for the user

 

 

32

 

 

5

 

USING THE HOB 

 

5.1

 

Ignition of the burners 

 

 

 

 

Before turning on the burners, make sure that the flame-spreader crowns 
and respective caps are properly fitted in their housings. Ensure the 
flame-spreader holes 

are aligned with the ignition plugs and the 

thermocouples. 

 

 

 

 

 

Panstand grid 

B

, available upon request, is intended for use with woks 

(Chinese pans). 
To prevent damage to the worktop, the hob is equipped with a raised grid 

C

: installs over pans larger than the diameter shown in the table in 

paragraph " 5.3 Diameter of receptacles". Note that pans larger than 28 
cm diameter must be used only on the central burner. 

 

 

 

 

 

 

 

 

 

 

 

 

A symbol next to each knob indicates the relative
burner. The device is fitted with electronic ignition.
Simply press and turn the knob counter-clockwise to 

the high flame symbol 

 until the burner is ignited.  

 

  In models with safety valve, after ignition, the knob has to be held down 

for a few seconds to allow the thermocouple to heat up. The burner 
might go off when the knob is released: this means the thermocouple 
has not heated up sufficiently. 
Wait a few moments and then repeat the operation, holding the knob 
down for longer. This operation is not necessary for burners without 
thermocouples. 
Once the burner is ignited, adjust the flame as required. 
Always check that the control knobs are in the position     (off) when you 
finish using the hob. 

Summary of Contents for PGF95-3


















Reviews: