background image

 

 

User instructions 

 

 

 

22

 

 

FAULT 

DESCRIPTION 

E7 

 

Turbine flow-regulator malfunction  

(for the relevant models only)

 

The appliance is not able to "measure" the amount 
of  water  loaded  accurately.  Interrupt  the  program 
and  switch  off  the  dishwasher.  Switch  the 
dishwasher back on, program it again and start the 
washing cycle. If the problem persists, contact the 
after-sales service.

 

E8 

 

Alternate washing system malfunction 

Interrupt the program and switch off the dishwasher. 
Switch the dishwasher back on, program it again and 
start the washing cycle. If the problem persists, contact 
the after-sales service. 

E9 

 

Water intake system malfunction 

Contact the after-sales service. 

E11 

  Wash motor pump does not work

 

 

 

Light off 

 

Light on 

 

Light flashing 

 

If an alarm occurs the appliance interrupts the program in progress and 
signals a fault. 

 

Alarms 

E1,  E2,  E3,  E4,  E8 

and 

E9

  interrupt  the  current  program 

immediately. 

 

The 

E5

E6

 alarms interrupts the running program once the cause is 

resolved, it will bring bach the execution of the program.

 

 

The  alarm 

E7

  is  visualized  at  the  end  of  the  cycle  that  comes, 

however, brought to the end since the operation of the dishwasher is 
not harmed.

 

 

E11:

 Contact the after-sales service.

 

 

To “reset” an alarm is necessary: 

Open and close the door, or turn off and on the machine. At this point 
is possible to program the dishwasher again.

 

 

 

 
 
 

If the malfunction persists, contact your authorised Service Centre. 

 

 

Summary of Contents for LSPU8212S























Reviews: