background image

3 - EN

2 Installation

Removing packaging reinforcement

Tilt the machine to remove the packaging 

reinforcement. Remove the packaging 

reinforcement by pulling the ribbon.

Opening the transportation locks

A

 Transportation safety bolts must be removed 

before operating the washing machine! 

Otherwise, the machine will be damaged!

1.  Loosen all the bolts with a spanner until they 

rotate freely (“C”)

2.  Remove transportation safety bolts by turning 

them gently.

3.  Fit the covers (supplied in the bag with the 

Operation Manual) into the holes on the rear 

panel. (“P”)

  

  

Keep the transportation safety bolts in a safe 

place to reuse when the washing machine 

needs to be moved again in the future.

Never move the appliance without the 

transportation safety bolts properly fixed in 

place!

Adjusting the feet

A

 Do not use any tools to loosen the lock nuts. 

Otherwise, they can be damaged.

1.  Manually (by hand) loosen the lock nuts on the 

feet.

2.  Adjust them until the machine stands level and 

firmly.

3.  Important: Tighten all lock nuts up again.

Connecting to the water supply.

Important:
•   The water supply pressure required to run the 

machine must be 1-10 bar (0,1 – 1 MPa).

•   Connect the special hoses supplied with the 

machine to the water intake valves on the 

machine. 

•  If you are going to use your double water-inlet 

machine as a single (cold) water-inlet unit, you 

must install the stopper*, supplied with your 

machine to the hot water valve.

•  If you want to use both water inlets of the 

product, you can connect the hot water hose 

after removing the stopper and gasket group 

from the hot water valve.

* Applies for the products supplied with a blind 

stopper group.
•  Models with a single water inlet should not be 

connected to the hot water tap.

When returning the appliance to its place after 

maintenance or cleaning, care should be taken not 

to fold, squeeze or block the hoses.

Connecting to the drain

The water discharge hose can be attached to the 

edge of a washbasin or bathtub. The drain hose 

should be firmly fitted into the drain as to not get 

out of its housing.
Important:
•   The end of the drain hose must be directly 

connected to the wastewater drain or to the 

washbasin.

•   The hose should be attached to a height of at 

least 40 cm, and 100 cm at most.

•   In case the hose is elevated after laying it on 

the floor level or close to the ground (less than 

40 cm above the ground), water discharge 

becomes more difficult and the laundry may 

come out wet.

•   The hose should be pushed into the drainage 

for more than 15 cm. If it is too long you may 

have it shortened.

•  The maximum length of the combined hoses 

must not be longer than 3.2 m.

Electrical connection

Connect the machine to an earthed outlet 

protected by a fuse of suitable capacity.
Important:

•   Connection should comply with national 

regulations.

•   The voltage and the allowed fuse protection 

are specified in the section “Technical 

Specifications”.

•   The specified voltage must be equal to your 

mains voltage.

•   Connection via extension cords or multi-plugs 

should not be made.

Summary of Contents for LBS126F













Reviews: