22
Functioning - Model with display
A
B
C
D
E
F
A -
Lighting, on/off.
B
- Fan off (Stand by)
C
- Timer for selected speed (visualizes the speed selected
and flashing LED on the lower side of the display).
This knob permits the operation of the cooker hood for a
established period:
20 minutes if the speed selected is
1
15 minutes if the speed selected is
2
10 minutes if the speed selected is
3
5 minutes if the intensive speed
P
is selected.
D
- Display showing:
•
Fan speed (1-3-P).
•
Change grease filters
(grease filter saturation
indicator -
F
)
After washing the anti-grease filter
, depress knob
B
for about 3 seconds. The letter
F
will disappear
from the display.
•
Change activated carbon filters
(carbon filter
saturation indicator -
C
).
After replacing the charcoal filter
, depress knob
B
for about 3 seconds. The letter
C
will disappear from
the display.
• When the led in the lower right side is on, it
indicates that the cooker hood is ready for operation
(“standby” position), the flashing LED indicates that
the timer has been activated for selected speed.
Warning!
The active carbon filter saturation function is not
activated.
In order to activate the carbon filter saturation indicator,
press buttons
E
and
F
simultaneously for 3 seconds.
Initially, only letter
F
will fbe displayed, then after the 3
seconds have passed, letter
C
will be displayed as well,
indicating that the carbon filter saturation control system
is active.
To switch off the system, re-press the same two buttons:
letter
C
appear on display and after 3 seconds letter it
disappear and the device will be switched off.
E
- Knob to decrease the speed: from intensive speed
P
to
speed level
1
.
F
- Knob to increase (standby) speed to intensive speed
P
.
Attention!
Intensive speed
P
has a duration of 5 minutes
after which the cooker hood automatically sets the speed
to level
2
(suction power).
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Warning!
Always press the fan off button
A
before disconnecting the
hood from the mains supply.
Functioning - 6-key electronic model
1
2
3
4
5 F 6
1
- Motor OFF key.
2
- Diminishes the speed.
3
- Increases the speed.
4
- 5/15 minutes timer. Inserts and extracts the timer.
The speed in function is turned off automatically.
5
- Resets carbon filters saturation indicator.
When the F led lights up, the carbon filter should be
cleaned or changed.
Press for at least 3 seconds after having changed the
carbon filter. The
F
led will turn off to indicate the
resetting of the saturation indicator.
Note:
This led switches ON even if the carbon filter has
not been mounted.
6
- ON/OFF
light.
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Electronic model with sensor
1 2 3 S
F C
Sensor
Reset
0/I
T1
T2
T3
T4
T5
1 2 3 4
T1.
Hood On/Off key
T2.
Increase cyclical motor speed key.
Pressing the first time activates speed 1. A Led (1-2-3),
corresponding to each speed, switches on. Led 4 flashes
at intensive speed.
After 5 minutes intensive speed is reduced to the second
speed. If key T2 is pressed before the end of the 5
minutes, the hood retunes to the first speed.
T5.
Lights On/Off key.
Filter signals
(function active with the hood on): the fats filter signal
appears after 80 hours functioning (Led 1 flashing).
The carbon filter signal appears after 320 hours (Led 2
flashing). In the case of simultaneous signalling of the
fats and carbon filters, Leds 1 and 2 flash alternatively.
Reset filter signals:
press key T4 for 3 seconds until Led 1 switches off (fats
filter). In the case of both filters (fats and carbon)
signalling, repeat the operation just described: pressing
T4 the first time switches off Leds 1 and 2 that are
flashing alternatively. Immediately afterwards Led 2
flashes again: at this point press T4 again for 3 seconds.
A beep signals each time the operation is completed.
Enabling the carbon filter signal:
the hood is enabled only for the fats filter signal. To
