Smeg ALFA135BM Instruction Manual Download Page 16

 

  

 

Additional instructions for steam ovens 

 

 

34

 

7.4

 

If the oven is not working properly 

 

This product meets the current safety regulations in force for 
electrical appliances. To prevent safety hazards for users, all 
technical inspections or repairs must be carried out by qualified 
persons. 

 

If the appliance is not working properly, before calling Customer Service, 
ensure that the procedures listed below have been performed. This will 
help to avoid unnecessary expenses. 

 
 

 

PROBLEM 

 

 

PROBABLE SOLUTION 

 

The oven is not working 

 

 

 

The minute minder knob is positioned on 0

 

The plug is not properly inserted in the socket. 

 

The electrical system is damaged or not 
working properly. 

 

The fuses have blown or the circuit breakers 
have been activated. 

 

 

Foods either take too long 
or too little to cook
 

 

 

The temperature setting is incorrect. 

 

 

No steam is being supplied 

 

 

 

The control knobs have not been positioned 
correctly. 

 

The oven door has not been closed properly. 

 

 

Moisture forms inside the 
oven and on the  foods
 

 

 

The foods are being left in the oven for too long 
after cooking. Do not leave them in the oven for 
more than 15-20 minutes after the end of the 
cooking time. 

 

 

There is water inside the 
oven
 

 

 

The device controlling the supply of water to 
the water reservoir is not working properly. 

 

 

Summary of Contents for ALFA135BM

















Reviews: